Savonius Rotor of 1m Diameter
|
Savonius Rotor of 1m Diameter Basic Data Category: Savonius wind turbines Keywords: savonius, rotor, diy, oho License: CC BY-SA 4.0 Organization: Youtube - Lerrypage Project status: Active Certification status: Approved Technical documentation
Contains PDF-drawings: Yes CAD files are editable: Yes Assembly instructions are published: No Bill of materials is published: Yes
yes yes
|
|
Technical documentation
Complete PDF plans | |
|
|
Files: | |
CAD files | |
|
|
Attestation | |
|
The project Savonius Rotor of 1m Diameter was reviewed by two reviewers from the OHO team. The review consisted of the following components:
1. Completeness check: Checks if all required documents have been submitted. 2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. 2.1 Bill of materials - Are all parts and assemblies covered? - Are all quantities correct? - Are all required material specifications available? - Are all specifications for purchased parts and standard parts complete? 3.2 Technical drawings - Are all the required views available? - Are all required dimensional data available? 4.1 Suggestions for improvement Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers Permanent Link: https://en.oho.wiki/index.php?title=Savonius_Rotor_of_1m_Diameter&oldid=44486 |
Files: | |
+ General Reviews 
Parts list
| Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
|---|---|---|---|---|---|---|---|---|
| A1 | 1 | 3D views |
REV1: Approved |
|
||||
| A2 | 1 | Exploded 3D view |
REV1: Approved |
|
||||
| B1 | Parts list |
REV1: Approved |
|
|||||
| C1 | Technical notes |
REV1: Approved |
|
|||||
| 1.0.0 | 1 | Rotor |
REV1: Approved |
|
||||
| 1.1.0 | 3 | Sheet steel | thickness: 1,0 mm, Galvanized Steel |
REV1: Approved |
|
|||
| 1.2.0 | 2 | Plate sheet | Production | thickness:1,0 mm, Galvanized Steel |
REV1: Approved |
|
||
| 1.3.0 | 1 | Support rotor |
REV1: Approved |
|
||||
| 1.3.1 | 2 | Tube support | Production | Schd 40, Steel A36 |
REV1: Approved |
|
||
| 1.3.2 | 2 | Angle | Production | L 25x25x3, Steel A36 |
REV1: Approved |
|
||
| 1.4.0 | 3 | Center sheet | Production | thickness: 1,0 mm, Galvanized Steel |
REV1: Approved |
|
||
| 2.0.0 | 1 | Lower shaft | Production | Steel C45 |
REV1: Approved |
|
||
| 3.0.0 | 1 | Tubular shaft | Production | Schd 40, Steel C45 |
REV1: Approved |
|
||
| 4.0.0 | 1 | Upper shaft | Production | Steel C45 |
REV1: Approved |
|
||
| 5.0.0 | 1 | Fly wheel | Buy | Fly wheel, medium, D:600 x1, Aluminum |
REV1: Approved |
|
||
| 6.0.0 | 1 | Fly wheel small | Buy | Fly wheel small, D:150 x1, Aluminum |
REV3: Approved |
|
||
| 7.0.0 | 1 | Belt transmission | Buy | Belt transmission, type V, Rubber |
REV1: Approved |
|
||
| 8.0.0 | Generator | Buy | Generator, DC Motor 80 V |
REV1: Approved |
|
|||
| 9.0.0 | 3 | Bearing | Standard | Bearing, Bridge UCPL207-107D1 |
REV1: Approved |
|
||
| 10.0.0 | 4 | Bolt shaft | Standard | Bolt shaft, M10 x L:50 DIN 933 |
REV1: Approved |
|
||
| 11.0.0 | 10 | Nut | Standard | Nut, Hex M10 DIN 934 |
REV1: Approved |
|
||