Difference between revisions of "Talk:Vice for drill press"
Inddigital (talk | contribs) ((by SublimeText.Mediawiker)) |
Inddigital (talk | contribs) ((by SublimeText.Mediawiker)) |
||
| Line 3: | Line 3: | ||
'''Round1:''' | '''Round1:''' | ||
[[User:Xtech2020 review|Xtech2020 review]] ([[User talk:Xtech2020 review|talk]]) 20:13, 3 November 2023 (CET) | [[User:Xtech2020 review|Xtech2020 review]] ([[User talk:Xtech2020 review|talk]]) 20:13, 3 November 2023 (CET) | ||
How do you ensure that the jaw moves aligned? An irregular piece can cause it to tilt and get stuck. | How do you ensure that the jaw moves aligned? An irregular piece can cause it to tilt and get stuck. | ||
| Line 22: | Line 22: | ||
'''Round1:''' | '''Round1:''' | ||
[[User:Aquilesmorillo|Aquilesmorillo]] ([[User talk:Aquilesmorillo|talk]]) 20:41, 3 November 2023 (CET) | [[User:Aquilesmorillo|Aquilesmorillo]] ([[User talk:Aquilesmorillo|talk]]) 20:41, 3 November 2023 (CET) | ||
For this type of manufacturing, I think that a double nut on both sides is unnecessary, with one welding point and two nuts it is enough | For this type of manufacturing, I think that a double nut on both sides is unnecessary, with one welding point and two nuts it is enough | ||
| Line 36: | Line 36: | ||
Permanent link to final Round 1 reviews: https://en.oho.wiki/index.php?title=Talk:Vice_for_drill_press&oldid=48237 | Permanent link to final Round 1 reviews: https://en.oho.wiki/index.php?title=Talk:Vice_for_drill_press&oldid=48237 | ||
== Part number 1 -- [[User:Xtech2020 review|Xtech2020 review]] ([[User talk:Xtech2020 review|talk]]) 21:13, 3 November 2023 (CET) | == Part number 1 -- [[User:Inddigital|Inddigital]] ([[User talk:Inddigital|talk]]) 23:39, 3 November 2023 (CET) == | ||
'''Round2:''' | |||
[[User:Xtech2020 review|Xtech2020 review]] ([[User talk:Xtech2020 review|talk]]) 21:13, 3 November 2023 (CET) | |||
How secure is that double nut joint? | How secure is that double nut joint? | ||
| Line 43: | Line 47: | ||
: For joints that are not subjected to extreme vibrations, it is safe. | : For joints that are not subjected to extreme vibrations, it is safe. | ||
[[User:Aquilesmorillo|Aquilesmorillo]] ([[User talk:Aquilesmorillo|talk]]) 21:41, 3 November 2023 (CET) | |||
The grade of threaded bar must be ensured to withstand wear and tear. | The grade of threaded bar must be ensured to withstand wear and tear. | ||
| Line 49: | Line 53: | ||
: Yes, the foresight was taken to look for a bar with greater resistance than those commonly used, a grade 5 | : Yes, the foresight was taken to look for a bar with greater resistance than those commonly used, a grade 5 | ||
[[User:Inddigital|Inddigital]] ([[User talk:Inddigital|talk]]) 23:45, 3 November 2023 (CET) | |||
'''Round 2 closed'''. No more edits for round 2 permitted. | |||
Permanent link to final Round 2 reviews: https://en.oho.wiki/index.php?title=Talk:Vice_for_drill_press&oldid=48249 | |||
Revision as of 00:51, 4 November 2023
Part number 1 -- Inddigital (talk) 22:39, 3 November 2023 (CET)
Round1:
Xtech2020 review (talk) 20:13, 3 November 2023 (CET)
How do you ensure that the jaw moves aligned? An irregular piece can cause it to tilt and get stuck.
- The vise will be used to hold flat pieces such as bars and plates so it would not be misaligned, however, some wedges between the rails can be considered to improve alignment in the case mentioned.
Part number 1 -- Inddigital (talk) 22:45, 3 November 2023 (CET)
Round 1 closed. No more edits for round 1 permitted.
Permanent link to final Round 1 reviews: https://en.oho.wiki/index.php?title=Talk:Vice_for_drill_press&oldid=48237
Part number 7 -- Inddigital (talk) 22:50, 3 November 2023 (CET)
Round1:
Aquilesmorillo (talk) 20:41, 3 November 2023 (CET)
For this type of manufacturing, I think that a double nut on both sides is unnecessary, with one welding point and two nuts it is enough
--Dev2023 (talk) 22:14, 3 November 2023 (CET)
In this device, we wanted not to use welding at all, however, for practicality an exception was made in the handle. If you are referring to the jaw joint, what you are suggesting makes sense, we will analyze it.
Part number 7 -- Inddigital (talk) 22:54, 3 November 2023 (CET)
Round 1 closed. No more edits for round 1 permitted.
Permanent link to final Round 1 reviews: https://en.oho.wiki/index.php?title=Talk:Vice_for_drill_press&oldid=48237
Part number 1 -- Inddigital (talk) 23:39, 3 November 2023 (CET)
Round2:
Xtech2020 review (talk) 21:13, 3 November 2023 (CET) How secure is that double nut joint?
- For joints that are not subjected to extreme vibrations, it is safe.
Aquilesmorillo (talk) 21:41, 3 November 2023 (CET) The grade of threaded bar must be ensured to withstand wear and tear.
- Yes, the foresight was taken to look for a bar with greater resistance than those commonly used, a grade 5
Inddigital (talk) 23:45, 3 November 2023 (CET)
Round 2 closed. No more edits for round 2 permitted.
Permanent link to final Round 2 reviews: https://en.oho.wiki/index.php?title=Talk:Vice_for_drill_press&oldid=48249