Small water turbine
Small water turbine Basic Data Category: Small Water turbines URL (first publication): https://dspace.mit.edu/handle/1721.1/27493 Keywords: turbine, hidraulic, turbomachinery, water, renewable, sustainable, electric power, mit License: CERN OHL v1.2 Organization: Practical Action Project status: Active Certification status: In process Technical documentation Maturity of the project: prototype
Contains PDF-drawings: Yes Assembly instructions are published: No Bill of materials is published: Yes
yes yes
|
|
Description
This project shows the construction plans for a small 5 kW water turbine based on the research of Dr. Mohammad Durali at MIT.
Project published under a CERN-OHL license
Technical documentation
PDF Plans | |
File:Oseg swt small-water-turbine.pdf | |
Files: |
CAD Files | |
Files: |
+ General Reviews
Parts list
Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
---|---|---|---|---|---|---|---|---|
A1 | small water turbine | A1 | Production | |||||
A2 | Presentation | A2 | Production | |||||
B | Parts-list | B |
REV1: Action required |
|||||
C | Technical notes | C | General notes | |||||
1 | 1 | front adaptor | 1 | Production | CAST IRON |
REV1: Action required |
||
2 | 1 | middle section | 2 | Production | CAST IRON |
REV1: Action required |
||
3 | 1 | drain chute | 3 | Production | STEEL C45 | |||
3.1 | back plate | 3.1 | Production | STEEL C45 |
REV1: Action required |
|||
3.2 | front flange | 3.2 | Production | STEEL C45 | ||||
3.3 | curved plate | 3.3 | Production | STEEL C45 |
REV1: Approved |
|||
3.4 | 2 | side plate | 3.4 | Production | STEEL C45 | |||
3.5 | front plate | 3.5 | Production | STEEL C45 | ||||
4 | nose | 4 | Production | See Technical notes |
REV1: Action required |
|||
5 | stator blading | 5 | Production | See Technical notes |
REV1: Action required |
|||
6 | rotor blading | 6 | Production | |||||
6.1 | rotor blading | 6.1 | Production | See Technical notes | ||||
6.2 | rotor washer | 6.2 | Production | 1,5 mm STEEL SHEET |
REV1: Action required |
|||
7 | diffuser blanding | 7 | Production | |||||
7.1 | diffuser blanding | 7.1 | Production | See Technical notes |
REV1: Action required |
|||
7.2 | diffuser washer | 7.2 | Production | 1,5 mm STEEL SHEET |
REV1: Action required |
|||
8 | bush | 8 | Production | see tech. notes | ||||
9 | slotted disk | 9 | Production | ALUMINIUM | ||||
10 | key | 10 | Standard | key 6 x 6 x 36.0, HARD STEEL | ||||
11 | Transmission (hub assembly) | 11 | Production | |||||
11.1 | shaft | 11.1 | Production | STAINLESS STEEL | ||||
11.2 | hub housing | 11.2 | Production | CAST STEEL | ||||
11.3 | front cap | 11.3 | Standard | 1,5 mm STEEL SHEET |
REV1: Approved |
|||
11.4 | ball bearing | 11.4 | Standard | bearing 206-SX adater and nut G-Y or equivalent estándar part | ||||
11.5 | seal | 11.5 | Standard | GARLOCK 78*0542 |
REV1: Approved |
|||
11.6 | big sprocket | 11.6 | Standard | brownign 40P60 - 1/2" pich - 60 teeth - Dia.: 9.55" | ||||
11.7 | small sprocket | 11.7 | Standard | brownign Nº 4024 - 1/2" pich - 24 teeth - Dia.: 3.83" | ||||
11.8 | chain | 11.8 | Standard | brownign Nº 40 - 1/2" pich Nº 40 | ||||
11.9 | bolt 3/16" x 32 x 5/16" | 11.9 | Standard | |||||
12 | frame | 12 | Production | |||||
12.1 | side angles | 12.1 | Production | steel A36 | ||||
12.2 | top angle | 12.2 | Production | steel A36 | ||||
12.3 | top plate | 12.3 | Production | steel A36 | ||||
12.4 | bar | 12.4 | Production | steel A36 | ||||
12.5 | foundation plate | 12.5 | Production | steel A36 | ||||
13 | oil bath cover | 13 | Production | |||||
13.1 | plate front cover | 13.1 | Production | 2-3 MM STEEL SHEET | ||||
13.2 | band side cover | 13.2 | Production | 2-3 MM STEEL SHEET | ||||
13.3 | plate down cover | 13.3 | Production | 2-3 MM STEEL SHEET | ||||
13.4 | brake angle cover | 13.4 | Production | STEEL A36 | ||||
13.5 | brake bar cover | 13.5 | Production | 2-3 MM STEEL SHEET | ||||
14 | back oil bath cover | 14 | Production | |||||
14.1 | plate back cover | 14.1 | Production | 2-3 MM STEEL SHEET | ||||
14.2 | bar for plate front | 14.2 | Production | 2-3 MM STEEL SHEET | ||||
15 | Generator | 15 | Standard | 5 KW; 115-230 V;21,5 A; 60Hz | ||||
16 | 20 | bolt 5/8"x12 - 2 1/2" | 16 | Standard | ||||
17 | 20 | nut 5/8"x12 | 17 | Standard | ||||
18 | 20 | plain washer 5/8" | 18 | Standard | ||||
19 | 4 | bolt 1/2"x12 - 1 1/2" | 19 | Standard | ||||
20 | 4 | nut 1/2"x12 | 20 | Standard | ||||
21 | 4 | plain washer 1/2" | 21 | Standard | ||||
22 | 4 | bolt 9/16"x12 - 2" | 22 | Standard | ||||
23 | 4 | nut 9/16"x12 | 23 | Standard | ||||
24 | 4 | plain washer 9/16" | 24 | Standard | ||||
25 | 4 | lock washer 9/16" | 25 | Standard | ||||
26 | 1 | bolt 3/8"x16 - 2" | 26 | Standard | ||||
27 | 2 | wing nut 3/8"x16 | 27 | Standard | ||||
28 | 1 | plain washer 3/8" | 28 | Standard | ||||
29 | 4 | ALIGNMENT-PIN | 29 | Standard | HARD STEEL | |||