Difference between revisions of "Small water turbine"
From OHO - search engine for sustainable open hardware projects
Inddigital (talk | contribs) |
Inddigital (talk | contribs) |
||
| Line 83: | Line 83: | ||
|matdrawingsheet=B | |matdrawingsheet=B | ||
|matpdffile=Oseg swt B part-list.pdf | |matpdffile=Oseg swt B part-list.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=C | |matpartnumber=C | ||
| Line 99: | Line 99: | ||
|matspec=CAST IRON | |matspec=CAST IRON | ||
|matpdffile=Oseg swt 1.0 front adaptor.pdf | |matpdffile=Oseg swt 1.0 front adaptor.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=2 | |matpartnumber=2 | ||
| Line 109: | Line 109: | ||
|matspec=CAST IRON | |matspec=CAST IRON | ||
|matpdffile=Oseg swt 2.0 middle section.pdf | |matpdffile=Oseg swt 2.0 middle section.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3 | |matpartnumber=3 | ||
| Line 127: | Line 127: | ||
|matspec=STEEL C45 | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.1 back plate.pdf | |matpdffile=Oseg swt 3.1 back plate.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.2 | |matpartnumber=3.2 | ||
| Line 170: | Line 170: | ||
|matspec=See Technical notes | |matspec=See Technical notes | ||
|matpdffile=Oseg swt 4.0 NOSE.pdf | |matpdffile=Oseg swt 4.0 NOSE.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=5 | |matpartnumber=5 | ||
| Line 179: | Line 179: | ||
|matspec=See Technical notes | |matspec=See Technical notes | ||
|matpdffile=Oseg swt 5.0 STATOR BLADING.pdf | |matpdffile=Oseg swt 5.0 STATOR BLADING.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=6 | |matpartnumber=6 | ||
| Line 200: | Line 200: | ||
|matspec=1,5 mm STEEL SHEET | |matspec=1,5 mm STEEL SHEET | ||
|matpdffile=Oseg swt 6.2 ROTOR WASHER.pdf | |matpdffile=Oseg swt 6.2 ROTOR WASHER.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=7 | |matpartnumber=7 | ||
| Line 214: | Line 214: | ||
|matspec=See Technical notes | |matspec=See Technical notes | ||
|matpdffile=Oseg swt 7.1 diffuser blanding.pdf | |matpdffile=Oseg swt 7.1 diffuser blanding.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=7.2 | |matpartnumber=7.2 | ||
| Line 222: | Line 222: | ||
|matspec=1,5 mm STEEL SHEET | |matspec=1,5 mm STEEL SHEET | ||
|matpdffile=Oseg swt 7.2 DIFFUSER WASHER.pdf | |matpdffile=Oseg swt 7.2 DIFFUSER WASHER.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=8 | |matpartnumber=8 | ||
Revision as of 02:56, 7 March 2021
|
Small water turbine Basic Data Category: Small Water turbines URL (first publication): https://dspace.mit.edu/handle/1721.1/27493 Keywords: turbine, hidraulic, turbomachinery, water, renewable, sustainable, electric power, mit License: CERN OHL v1.2 Organization: Practical Action Project status: Active Certification status: In process Technical documentation Maturity of the project: prototype
Contains PDF-drawings: Yes Assembly instructions are published: No Bill of materials is published: Yes
yes yes
|
|
Description
This project shows the construction plans for a small 5 kW water turbine based on the research of Dr. Mohammad Durali at MIT.
Project published under a CERN-OHL license
Technical documentation
PDF Plans | |
| File:Oseg swt small-water-turbine.pdf | |
Files: | |
CAD Files | |
|
|
Files: | |
+ General Reviews 
Parts list
| Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
|---|---|---|---|---|---|---|---|---|
| A1 | small water turbine | A1 | Production | |
||||
| A2 | Presentation | A2 | Production | |
||||
| B | Parts-list | B |
REV1: Approved |
|
||||
| C | Technical notes | C | General notes | |
||||
| 1 | 1 | front adaptor | 1 | Production | CAST IRON |
REV1: Approved |
|
|
| 2 | 1 | middle section | 2 | Production | CAST IRON |
REV1: Approved |
|
|
| 3 | 1 | drain chute | 3 | Production | STEEL C45 | |
||
| 3.1 | back plate | 3.1 | Production | STEEL C45 |
REV1: Approved |
|
||
| 3.2 | front flange | 3.2 | Production | STEEL C45 | |
|||
| 3.3 | curved plate | 3.3 | Production | STEEL C45 |
REV1: Approved |
|
||
| 3.4 | 2 | side plate | 3.4 | Production | STEEL C45 | |
||
| 3.5 | front plate | 3.5 | Production | STEEL C45 | |
|||
| 4 | nose | 4 | Production | See Technical notes |
REV1: Approved |
|
||
| 5 | stator blading | 5 | Production | See Technical notes |
REV1: Approved |
|
||
| 6 | rotor blading | 6 | Production | |
||||
| 6.1 | rotor blading | 6.1 | Production | See Technical notes | |
|||
| 6.2 | rotor washer | 6.2 | Production | 1,5 mm STEEL SHEET |
REV1: Approved |
|
||
| 7 | diffuser blanding | 7 | Production | |
||||
| 7.1 | diffuser blanding | 7.1 | Production | See Technical notes |
REV1: Approved |
|
||
| 7.2 | diffuser washer | 7.2 | Production | 1,5 mm STEEL SHEET |
REV1: Approved |
|
||
| 8 | bush | 8 | Production | see tech. notes | |
|||
| 9 | slotted disk | 9 | Production | ALUMINIUM | |
|||
| 10 | key | 10 | Standard | key 6 x 6 x 36.0, HARD STEEL | |
|||
| 11 | Transmission (hub assembly) | 11 | Production | |
||||
| 11.1 | shaft | 11.1 | Production | STAINLESS STEEL | |
|||
| 11.2 | hub housing | 11.2 | Production | CAST STEEL | |
|||
| 11.3 | front cap | 11.3 | Standard | 1,5 mm STEEL SHEET |
REV1: Approved |
|
||
| 11.4 | ball bearing | 11.4 | Standard | bearing 206-SX adater and nut G-Y or equivalent estándar part | |
|||
| 11.5 | seal | 11.5 | Standard | GARLOCK 78*0542 |
REV1: Approved |
|
||
| 11.6 | big sprocket | 11.6 | Standard | brownign 40P60 - 1/2" pich - 60 teeth - Dia.: 9.55" | |
|||
| 11.7 | small sprocket | 11.7 | Standard | brownign Nº 4024 - 1/2" pich - 24 teeth - Dia.: 3.83" | |
|||
| 11.8 | chain | 11.8 | Standard | brownign Nº 40 - 1/2" pich Nº 40 | |
|||
| 11.9 | bolt 3/16" x 32 x 5/16" | 11.9 | Standard | |
||||
| 12 | frame | 12 | Production | |
||||
| 12.1 | side angles | 12.1 | Production | steel A36 | |
|||
| 12.2 | top angle | 12.2 | Production | steel A36 | |
|||
| 12.3 | top plate | 12.3 | Production | steel A36 | |
|||
| 12.4 | bar plate | 12.4 | Production | steel A36 | |
|||
| 12.5 | foundation plate | 12.5 | Production | steel A36 | |
|||
| 13 | oil bath cover | 13 | Production | |
||||
| 13.1 | plate front cover | 13.1 | Production | 2-3 MM STEEL SHEET | |
|||
| 13.2 | band side cover | 13.2 | Production | 2-3 MM STEEL SHEET | |
|||
| 13.3 | plate down cover | 13.3 | Production | 2-3 MM STEEL SHEET | |
|||
| 13.4 | brake angle cover | 13.4 | Production | STEEL A36 | |
|||
| 13.5 | brake bar cover | 13.5 | Production | 2-3 MM STEEL SHEET | |
|||
| 14 | back oil bath cover | 14 | Production | |
||||
| 14.1 | plate back cover | 14.1 | Production | 2-3 MM STEEL SHEET | |
|||
| 14.2 | bar for plate front | 14.2 | Production | 2-3 MM STEEL SHEET | |
|||
| 15 | Generator | 15 | Standard | 5 KW; 115-230 V;21,5 A; 60Hz | |
|||
| 16 | 20 | bolt 5/8"x12 - 2 1/2" | 16 | Standard | |
|||
| 17 | 20 | nut 5/8"x12 | 17 | Standard | |
|||
| 18 | 20 | plain washer 5/8" | 18 | Standard | |
|||
| 19 | 4 | bolt 1/2"x12 - 1 1/2" | 19 | Standard | |
|||
| 20 | 4 | nut 1/2"x12 | 20 | Standard | |
|||
| 21 | 4 | plain washer 1/2" | 21 | Standard | |
|||
| 22 | 4 | bolt 9/16"x12 - 2" | 22 | Standard | |
|||
| 23 | 4 | nut 9/16"x12 | 23 | Standard | |
|||
| 24 | 4 | plain washer 9/16" | 24 | Standard | |
|||
| 25 | 4 | lock washer 9/16" | 25 | Standard | |
|||
| 26 | 1 | bolt 3/8"x16 - 2" | 26 | Standard | |
|||
| 27 | 2 | wing nut 3/8"x16 | 27 | Standard | |
|||
| 28 | 1 | plain washer 3/8" | 28 | Standard | |
|||
| 29 | 4 | ALIGNMENT-PIN | 29 | Standard | HARD STEEL | |
||