Difference between revisions of "Savonius Rotor of 1m Diameter"
(19 intermediate revisions by 4 users not shown) | |||
Line 45: | Line 45: | ||
|cmptitle=CAD files | |cmptitle=CAD files | ||
|cmpimage=Jha srd savonius-rotor-1m-diameter 0001.jpg | |cmpimage=Jha srd savonius-rotor-1m-diameter 0001.jpg | ||
}}{{ProjektComponent | |||
|cmptitle=Attestation | |||
|cmpimage=Attestation Savonius Rotor of 1m Diameter.jpg | |||
|cmpimg=The project Savonius Rotor of 1m Diameter was reviewed by two reviewers from the OHO team. The review consisted of the following components: | |||
1. Completeness check: Checks if all required documents have been submitted. | |||
2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. | |||
2.1 Bill of materials | |||
- Are all parts and assemblies covered? | |||
- Are all quantities correct? | |||
- Are all required material specifications available? | |||
- Are all specifications for purchased parts and standard parts complete? | |||
3.2 Technical drawings | |||
- Are all the required views available? | |||
- Are all required dimensional data available? | |||
4.1 Suggestions for improvement | |||
Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers | |||
Permanent Link: https://en.oho.wiki/index.php?title=Savonius_Rotor_of_1m_Diameter&oldid=44486 | |||
|cmpfile1=Attestation Savonius Rotor of 1m Diameter.pdf | |||
}} | |||
|Materials={{ProjektMaterials | |||
|matpartnumber=A1 | |||
|matquantity=1 | |||
|matdesc=3D views | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter A1.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=A2 | |||
|matquantity=1 | |||
|matdesc=Exploded 3D view | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter A2.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=B1 | |||
|matdesc=Parts list | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter B1.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=C1 | |||
|matdesc=Technical notes | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter C1.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.0.0 | |||
|matquantity=1 | |||
|matdesc=Rotor | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter 1.0.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.1.0 | |||
|matquantity=3 | |||
|matdesc=Sheet steel | |||
|matspec=thickness: 1,0 mm, Galvanized Steel | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter 1.1.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.2.0 | |||
|matquantity=2 | |||
|matdesc=Plate sheet | |||
|matparttype=production | |||
|matspec=thickness:1,0 mm, Galvanized Steel | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter 1.2.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.3.0 | |||
|matquantity=1 | |||
|matdesc=Support rotor | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter 1.3.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.3.1 | |||
|matquantity=2 | |||
|matdesc=Tube support | |||
|matparttype=production | |||
|matspec=Schd 40, Steel A36 | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter 1.3.1.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.3.2 | |||
|matquantity=2 | |||
|matdesc=Angle | |||
|matparttype=production | |||
|matspec=L 25x25x3, Steel A36 | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter 1.3.2.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.4.0 | |||
|matquantity=3 | |||
|matdesc=Center sheet | |||
|matparttype=production | |||
|matspec=thickness: 1,0 mm, Galvanized Steel | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter 1.4.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.0.0 | |||
|matquantity=1 | |||
|matdesc=Lower shaft | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter 2.0.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.0.0 | |||
|matquantity=1 | |||
|matdesc=Tubular shaft | |||
|matparttype=production | |||
|matspec=Schd 40, Steel C45 | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter 3.0.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=4.0.0 | |||
|matquantity=1 | |||
|matdesc=Upper shaft | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Jha srd savonius-rotor-1m-diameter 4.0.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=5.0.0 | |||
|matquantity=1 | |||
|matdesc=Fly wheel | |||
|matparttype=buy | |||
|matspec=Fly wheel, medium, D:600 x1, Aluminum | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=6.0.0 | |||
|matquantity=1 | |||
|matdesc=Fly wheel small | |||
|matparttype=buy | |||
|matspec=Fly wheel small, D:150 x1, Aluminum | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=7.0.0 | |||
|matquantity=1 | |||
|matdesc=Belt transmission | |||
|matparttype=buy | |||
|matspec=Belt transmission, type V, Rubber | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=8.0.0 | |||
|matdesc=Generator | |||
|matparttype=buy | |||
|matspec=Generator, DC Motor 80 V | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=9.0.0 | |||
|matquantity=3 | |||
|matdesc=Bearing | |||
|matparttype=standard | |||
|matspec=Bearing, Bridge UCPL207-107D1 | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=10.0.0 | |||
|matquantity=4 | |||
|matdesc=Bolt shaft | |||
|matparttype=standard | |||
|matspec=Bolt shaft, M10 x L:50 DIN 933 | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=11.0.0 | |||
|matquantity=10 | |||
|matdesc=Nut | |||
|matparttype=standard | |||
|matspec=Nut, Hex M10 DIN 934 | |||
|status_rev_1=approved | |||
|status_rev_3=approved | |||
}} | }} | ||
|certificate_requested=No | |certificate_requested=No | ||
|certificate_status= | |certificate_status=approved | ||
|reviewer1=Dmosquera1968 | |||
|reviewer2=Jaimerosciano | |||
|reviewer3=Jeefri | |||
}} | }} |
Latest revision as of 11:59, 18 January 2022
Savonius Rotor of 1m Diameter Basic Data Category: Savonius wind turbines Keywords: savonius, rotor, diy, oho License: CC BY-SA 4.0 Organization: Youtube - Lerrypage Project status: Active Certification status: Approved Technical documentation
Contains PDF-drawings: Yes CAD files are editable: Yes Assembly instructions are published: No Bill of materials is published: Yes
yes yes
|
|
Technical documentation
Complete PDF plans | |
Files: |
Attestation | |
The project Savonius Rotor of 1m Diameter was reviewed by two reviewers from the OHO team. The review consisted of the following components:
1. Completeness check: Checks if all required documents have been submitted. 2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. 2.1 Bill of materials - Are all parts and assemblies covered? - Are all quantities correct? - Are all required material specifications available? - Are all specifications for purchased parts and standard parts complete? 3.2 Technical drawings - Are all the required views available? - Are all required dimensional data available? 4.1 Suggestions for improvement Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers Permanent Link: https://en.oho.wiki/index.php?title=Savonius_Rotor_of_1m_Diameter&oldid=44486 | |
Files: |
+ General Reviews
Parts list
Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
---|---|---|---|---|---|---|---|---|
A1 | 1 | 3D views |
REV1: Approved |
|||||
A2 | 1 | Exploded 3D view |
REV1: Approved |
|||||
B1 | Parts list |
REV1: Approved |
||||||
C1 | Technical notes |
REV1: Approved |
||||||
1.0.0 | 1 | Rotor |
REV1: Approved |
|||||
1.1.0 | 3 | Sheet steel | thickness: 1,0 mm, Galvanized Steel |
REV1: Approved |
||||
1.2.0 | 2 | Plate sheet | Production | thickness:1,0 mm, Galvanized Steel |
REV1: Approved |
|||
1.3.0 | 1 | Support rotor |
REV1: Approved |
|||||
1.3.1 | 2 | Tube support | Production | Schd 40, Steel A36 |
REV1: Approved |
|||
1.3.2 | 2 | Angle | Production | L 25x25x3, Steel A36 |
REV1: Approved |
|||
1.4.0 | 3 | Center sheet | Production | thickness: 1,0 mm, Galvanized Steel |
REV1: Approved |
|||
2.0.0 | 1 | Lower shaft | Production | Steel C45 |
REV1: Approved |
|||
3.0.0 | 1 | Tubular shaft | Production | Schd 40, Steel C45 |
REV1: Approved |
|||
4.0.0 | 1 | Upper shaft | Production | Steel C45 |
REV1: Approved |
|||
5.0.0 | 1 | Fly wheel | Buy | Fly wheel, medium, D:600 x1, Aluminum |
REV1: Approved |
|||
6.0.0 | 1 | Fly wheel small | Buy | Fly wheel small, D:150 x1, Aluminum |
REV3: Approved |
|||
7.0.0 | 1 | Belt transmission | Buy | Belt transmission, type V, Rubber |
REV1: Approved |
|||
8.0.0 | Generator | Buy | Generator, DC Motor 80 V |
REV1: Approved |
||||
9.0.0 | 3 | Bearing | Standard | Bearing, Bridge UCPL207-107D1 |
REV1: Approved |
|||
10.0.0 | 4 | Bolt shaft | Standard | Bolt shaft, M10 x L:50 DIN 933 |
REV1: Approved |
|||
11.0.0 | 10 | Nut | Standard | Nut, Hex M10 DIN 934 |
REV1: Approved |
|||