Difference between revisions of "Cross Flow Turbine"
(3 intermediate revisions by one other user not shown) | |||
Line 67: | Line 67: | ||
|cmpfile1=Oseg cft CAD-files.zip | |cmpfile1=Oseg cft CAD-files.zip | ||
|cmpfile2=Oseg cft STP-files.zip | |cmpfile2=Oseg cft STP-files.zip | ||
}}{{ProjektComponent | |||
|cmptitle=Attestation | |||
|cmpimage=Attestation Cross Flow Turbine.jpg | |||
|cmpimg=The project Cross Flow Turbine was reviewed by two reviewers from the OHO team. The review consisted of the following components: | |||
1. Completeness check: Checks if all required documents have been submitted. | |||
2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. | |||
2.1 Bill of materials | |||
- Are all parts and assemblies covered? | |||
- Are all quantities correct? | |||
- Are all required material specifications available? | |||
- Are all specifications for purchased parts and standard parts complete? | |||
3.2 Technical drawings | |||
- Are all the required views available? | |||
- Are all required dimensional data available? | |||
4.1 Suggestions for improvement | |||
Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers | |||
Permanent Link: https://en.oho.wiki/index.php?title=Cross_Flow_Turbine&oldid=44328 | |||
|cmpfile1=Attestation Cross Flow Turbine.vsdx.pdf | |||
}} | }} | ||
|Materials={{ProjektMaterials | |Materials={{ProjektMaterials | ||
Line 876: | Line 901: | ||
|matquantity=8 | |matquantity=8 | ||
|matdesc=Bolt M6x50 | |matdesc=Bolt M6x50 | ||
|matdrawingsheet=8.0.0 | |||
|matparttype=standard | |matparttype=standard | ||
|matspec=Bolt M6x50 | |matspec=Bolt M6x50 | ||
Line 882: | Line 908: | ||
|matquantity=8 | |matquantity=8 | ||
|matdesc=screw 10Mx50 | |matdesc=screw 10Mx50 | ||
|matdrawingsheet=9.0.0 | |||
|matparttype=standard | |matparttype=standard | ||
|matspec=screw 10Mx50 | |matspec=screw 10Mx50 | ||
Line 888: | Line 915: | ||
|matquantity=18 | |matquantity=18 | ||
|matdesc=Bolt M12x30 | |matdesc=Bolt M12x30 | ||
|matdrawingsheet=10.0.0 | |||
|matparttype=standard | |||
|matspec=Bolt M12x30 | |matspec=Bolt M12x30 | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 961: | Line 990: | ||
}} | }} | ||
|certificate_requested=No | |certificate_requested=No | ||
|certificate_status= | |certificate_status=approved | ||
|reviewer1=Jaimerosciano | |reviewer1=Jaimerosciano | ||
|reviewer2=Jeefri | |reviewer2=Jeefri | ||
|reviewer3=Dmosquera1968 | |reviewer3=Dmosquera1968 | ||
}} | }} |
Revision as of 12:08, 18 January 2022
Cross Flow Turbine Basic Data Category: Cross flow turbines URL (first publication): https://www.youtube.com/watch?v=QjnxpPr1DPQ Keywords: turbine, cross flow, hidraulic, turbomachinery, impulse, reaction, water, renewable, sustainable, electric power, skat License: CC BY-SA 4.0 Organization: Skat Project status: Active Certification status: Approved Technical documentation
Contains PDF-drawings: Yes CAD files are editable: Yes Assembly instructions are published: Yes Bill of materials is published: Yes
yes yes
|
Description
technical drawings and 3d models for a complete cross-flow turbine assembly.
project published under license CC-BY-SA 4.0
This project was supported by the german Foundation E.ON Stiftung.
Technical documentation
PDF Plans | |
Files: |
CAD Files | |
Files: |
Attestation | |
The project Cross Flow Turbine was reviewed by two reviewers from the OHO team. The review consisted of the following components:
1. Completeness check: Checks if all required documents have been submitted. 2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. 2.1 Bill of materials - Are all parts and assemblies covered? - Are all quantities correct? - Are all required material specifications available? - Are all specifications for purchased parts and standard parts complete? 3.2 Technical drawings - Are all the required views available? - Are all required dimensional data available? 4.1 Suggestions for improvement Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers Permanent Link: https://en.oho.wiki/index.php?title=Cross_Flow_Turbine&oldid=44328 | |
Files: |
+ General Reviews
Parts list
Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
---|---|---|---|---|---|---|---|---|
A1 | 1 | Cross flow turbine | A1 |
REV1: Approved |
||||
A2 | 1 | Cross-flow-turbine | A2 |
REV1: Approved |
||||
B1 | PART LIST | B1 |
REV1: Approved |
|||||
C1 | TECH NOTES | C1 |
REV1: Approved |
|||||
1.0.0 | 1 | Base frame | 1.0.0 |
REV1: Approved |
||||
1.1.0 | 2 | Channel100x50x70 | 1.1.0 | Production | structural steel, ASTM-A36 |
REV1: Approved |
||
1.2.0 | 1 | Channel100x50x475 | 1.2.0 | Production | structural steel, ASTM-A36 |
REV1: Approved |
||
1.3.0 | 1 | Channel100x50x545 | 1.3.0 | Production | structural steel, ASTM-A36 |
REV1: Approved |
||
1.4.0 | 2 | Rubber6mmx425 | 1.4.0 | Production | rubber |
REV1: Approved |
||
1.5.0 | 2 | Rubber-6mmx395 | 1.5.0 | Production | rubber |
REV1: Approved |
||
2.0.0 | 1 | Rotor-housing | 2.0.0 |
REV1: Approved |
||||
2.1.0 | 2 | Side plate | 2.1.0 | Production | steel C45 |
REV1: Approved |
||
2.2.0 | 1 | Baffle plate | 2.2.0 | Production | steel C45 |
REV1: Approved |
||
2.3.0 | 1 | oseg_cft_spacer-plate | 2.3.0 | Production | steel C45 |
REV1: Approved |
||
2.4.0 | 1 | oseg_cft_rear-baffle-plate | 2.4.0 | Production | steel C45 |
REV1: Approved |
||
2.5.0 | 1 | Houseing base front | 2.5.0 | Production | steel C45 |
REV1: Approved |
||
2.6.0 | 1 | Houseing-base-rear | 2.6.0 | Production | steel C45 |
REV1: Approved |
||
2.7.0 | 8 | Thear-stub | 2.7.0 | Production | steel C45 |
REV1: Approved |
||
2.8.0 | 1 | Rib | 2.8.0 | Production | steel C45 |
REV1: Approved |
||
2.9.0 | 2 | Bracing plate | 2.9.0 | Production | steel C45 |
REV1: Approved |
||
3.0.0 | 1 | Inlet top | 3.0.0 |
REV1: Approved |
||||
3.1.0 | 1 | Hatch door | 3.1.0 |
REV1: Approved |
||||
3.1.1 | 1 | Hatch door sheet02 | 3.1.1 | Production | Steel C45 |
REV1: Approved |
||
3.1.2 | 2 | Hatch door frame L25x325 | 3.1.2 | Production | ASTM-A36 |
REV1: Approved |
||
3.1.3 | 1 | oseg_cft_Hatch-door-sheet | 3.1.3 | Production | Steel C45 |
REV1: Approved |
||
3.1.4 | 2 | Handle | 3.1.4 | Production | ASTM-A36 |
REV1: Approved |
||
3.1.5 | 20 | Bolt-M6x20 | Standard | |||||
3.1.6 | 20 | Nut M | Standard | |||||
3.2.0 | 2 | Hatch door frame L25x260 | 3.2.0 | Production | structural steel, ASTM A-36 |
REV1: Approved |
||
3.3.0 | 2 | Hatch door frame L25x345 | 3.3.0 | Production | Angle 25x25x5, ASTM A-36 |
REV1: Approved |
||
3.4.0 | 2 | Inlet side plate | 3.4.0 | Production | Steel C45 |
REV1: Approved |
||
3.5.0 | 1 | Inlet top guide | 3.5.0 | Production | Steel C45 |
REV1: Approved |
||
3.6.0 | 2 | Inlet flange | 3.6.0 | Production | Steel C45 |
REV1: Approved |
||
3.7.0 | 2 | Inlet flange2 | 3.7.0 | Production | Steel C45 |
REV1: Approved |
||
3.8.0 | 1 | Inlet bottom plate | 3.8.0 | Production | Steel C45 |
REV1: Approved |
||
3.9.0 | 1 | Inle-gasket | 3.9.0 | Production | Rubber |
REV1: Approved |
||
4.0.0 | 1 | Rotor | 4.0.0 |
REV1: Approved |
||||
4.1.0 | 1 | Rotor shaft | 4.1.0 | Production | Steel C45 hardened |
REV1: Approved |
||
4.2.0 | 3 | Rotor disc | 4.2.0 | Production | Steel C45 |
REV1: Approved |
||
4.3.0 | 32 | Blade | 4.3.0 | Production | Steel C45 |
REV1: Approved |
||
5.0.0 | 2 | Stuffing box | 5.0.0 |
REV1: Approved |
||||
5.1.0 | 2 | Stuffing box02 | 5.1.0 | Production | Steel C45 |
REV1: Approved |
||
5.2.0 | 2 | Stuffin plate gasket | 5.2.0 | Production | Rubber |
REV1: Approved |
||
5.3.0 | 2 | Stuffing box01 | 5.3.0 | Production | Steel C45 |
REV1: Approved |
||
5.4.0 | 2 | Press ring | 5.4.0 | Production | Steel C45 |
REV1: Approved |
||
5.5.0 | 4 | Spacer | 5.5.0 | Production | Steel C45 |
REV1: Approved |
||
5.6.0 | 2 | Rotor bearing | 5.6.0 | Buy | BEARING NUMBER FYH F21OJ UCSlO |
REV1: Approved |
||
6.0.0 | 1 | Butterfly Valve | 6.0.0 |
REV1: Approved |
||||
6.1.0 | 1 | Cover | 6.1.0 | Production | Steel C45 |
REV1: Approved |
||
6.2.0 | 1 | Gasket | 6.2.0 | Production | Rubber |
REV1: Approved |
||
6.3.0 | 2 | Washer | 6.3.0 | Production | Steel C45 |
REV1: Approved |
||
6.4.0 | 1 | Bush casing 2 | 6.4.0 | Steel C45 |
REV1: Approved |
|||
6.5.0 | 1 | Bush casing | 6.5.0 | Production | Steel C45 |
REV1: Approved |
||
6.6.0 | 1 | Valve shaft | 6.6.0 | Production | Steel C45 hardened |
REV1: Approved |
||
6.7.0 | 1 | Butterfly Valve shaft | 6.7.0 |
REV1: Approved |
||||
6.7.1 | 1 | shaft valve 1 | 6.7.1 | Production | Steel C45 |
REV1: Approved |
||
6.7.2 | 1 | shaft valve 2 | 6.7.2 | Steel C45 |
REV1: Approved |
|||
6.7.3 | 3 | Shaft valve 3 | 6.7.3 | Production | Steel C45 |
REV1: Approved |
||
6.7.4 | 1 | shaft valve 4 | 6.7.4 | Production | Steel C45 |
REV1: Approved |
||
6.8.0 | 1 | Lever | 6.8.0 | Steel C45 |
REV1: Approved |
|||
7.0.0 | 1 | Support | 7.0.0 |
REV1: Approved |
||||
7.1.0 | 1 | Support angle | 7.1.0 | Structural steel, ASTM-A36 |
REV1: Approved |
|||
7.2.0 | Stopper top plate | 7.2.0 | Steel C45 |
REV1: Approved |
||||
7.3.0 | 1 | Stopper plate top | 7.3.0 | Steel C45 |
REV1: Approved |
|||
7.4.0 | 1 | Stopper plate bottom | 7.4.0 | Steel C45 |
REV1: Approved |
|||
7.5.0 | 1 | Base plate | 7.5.0 | Steel C45 |
REV1: Approved |
|||
7.6.0 | 1 | Handle bar | 7.6.0 | Steel C45 |
REV1: Approved |
|||
7.7.0 | 1 | Knob ring | 7.7.0 | Steel C45 |
REV1: Approved |
|||
7.8.0 | 1 | Bush | 7.8.0 | Production | Steel C45 |
REV1: Approved |
||
7.9.0 | 1 | Spindle | 7.9.0 | Steel C45 |
REV1: Approved |
|||
7.10.0 | 1 | Lock-nut | 7.10.0 | Steel C45 |
REV1: Approved |
|||
7.11.0 | 1 | Wing nutM16 | 7.11.0 | Steel C45 |
REV1: Approved |
|||
8.0.0 | 8 | Bolt M6x50 | 8.0.0 | Standard | Bolt M6x50 | |||
9.0.0 | 8 | screw 10Mx50 | 9.0.0 | Standard | screw 10Mx50 | |||
10.0.0 | 18 | Bolt M12x30 | 10.0.0 | Standard | Bolt M12x30 | |||
11.0.0 | 8 | Nut M6 | 11.0.0 | Standard | Nut M6 |
REV1: Approved |
||
12.0.0 | 18 | Nut M12 | 12.0.0 | Standard | Nut M12 |
REV1: Approved |
||
13.0.0 | 1 | Adapter | 13.0.0 |
REV1: Approved |
||||
13.1.0 | 2 | Sdapter flange | 13.1.0 | Steel C45 |
REV1: Approved |
|||
13.2.0 | 2 | Adapter flange2 | 13.2.0 | Steel C45 |
REV1: Approved |
|||
13.3.0 | 1 | Shaft-adapter | 13.3.0 | Steel C45 |
REV1: Approved |
|||
13.4.0 | 1 | Penstock-flange | 13.4.0 | Steel C45 |
REV1: Approved |
|||