Difference between revisions of "Talk:Zigzag Solar water heater"
From OHO - search engine for sustainable open hardware projects
(→Part number 1.2 -- ~~~~: new section) |
(→Part number 1.3 -- ~~~~: new section) |
||
Line 66: | Line 66: | ||
What are the standard sizes for galvanized sheets? so as not to waste material. | What are the standard sizes for galvanized sheets? so as not to waste material. | ||
== Part number 1.3 -- [[User:Xtech2020 review|Xtech2020 review]] ([[User talk:Xtech2020 review|talk]]) 20:38, 4 March 2021 (CET) == | |||
Wouldn't it be easier to buy these parts |
Revision as of 21:38, 4 March 2021
Part number B -- Xtech2020 review (talk) 03:33, 3 March 2021 (CET)
It seems that the containers used are 200 L, however, in the part list it says 2000 L.
Part number 1.3 -- Xtech2020 review (talk) 03:41, 3 March 2021 (CET)
The amount shown on the drawings is 16
Re: Part number 1.3 -- Inddigital (talk) 05:01, 4 March 2021 (CET)
- Thanks for the comment, I'll check that out
Part number 1.4 -- Xtech2020 review (talk) 03:44, 3 March 2021 (CET)
The amount shown on the drawings is 64
Re: Part number 1.4 -- Inddigital (talk) 05:02, 4 March 2021 (CET)
- Thanks for the comment, I'll check that out
-- Xtech2020 review (talk) 03:47, 3 March 2021 (CET)
Indicate the estimated capacity of the equipment
Re: -- Inddigital (talk) 04:57, 4 March 2021 (CET)
- According to the original source, when a system is properly insulated, hot water can be drawn 24 hours a day.
Part number B -- Xtech2020 review (talk) 04:34, 4 March 2021 (CET)
you must place the material of the pieces in the column specifications
Part number B -- Xtech2020 review (talk) 04:35, 4 March 2021 (CET)
The sheet column should be updated
Part number 2.7 -- Xtech2020 review (talk) 04:40, 4 March 2021 (CET)
This part must be marked on the drawing of Assembly 2
Part number 1.3 -- Xtech2020 review (talk) 04:45, 4 March 2021 (CET)
specify material
Re: Part number 1.3 -- Inddigital (talk) 05:17, 4 March 2021 (CET)
- I have just updated this item in the part list, then, when I do the rest of the checks, I will proceed with the respective pages of the PDF.
Part number 3.1 -- Xtech2020 review (talk) 04:47, 4 March 2021 (CET)
200 L container
Part number 4.1 -- Xtech2020 review (talk) 04:49, 4 March 2021 (CET)
Half of a 200 L container
Part number A1 -- Xtech2020 review (talk) 20:00, 4 March 2021 (CET)
The direction of water flow is nowhere to be seen, a hydraulic diagram is needed.
Part number A1 -- Xtech2020 review (talk) 20:24, 4 March 2021 (CET)
the slip of each collector with respect to its neighboring collector is not specified.
Part number 1.2 -- Xtech2020 review (talk) 20:36, 4 March 2021 (CET)
What are the standard sizes for galvanized sheets? so as not to waste material.
Part number 1.3 -- Xtech2020 review (talk) 20:38, 4 March 2021 (CET)
Wouldn't it be easier to buy these parts