Difference between revisions of "Talk:Solar Water Heater - Capacity 100L"
Inddigital (talk | contribs) ((by SublimeText.Mediawiker)) |
Inddigital (talk | contribs) ((by SublimeText.Mediawiker)) |
||
Line 11: | Line 11: | ||
== -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 23:50, 12 January 2023 (CEST) == | == -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 23:50, 12 January 2023 (CEST) == | ||
The perforations are missing in the insulating walls for the pipes to pass through, although it is not a critical detail, this can be quickly deduced during manufacturing | The perforations are missing in the insulating walls for the pipes to pass through, although it is not a critical detail, this can be quickly deduced during manufacturing | ||
: Copied, it will be added in the next version of the plans | |||
: --[[User:Inddigital|Inddigital]] ([[User talk:Inddigital|talk]]) 02:45, 25 January 2023 (CET) | |||
== Part number 4.00 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 23:52, 12 January 2023 (CEST) == | == Part number 4.00 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 23:52, 12 January 2023 (CEST) == | ||
It is recommended to evaluate if it is necessary to place flexible sections in the pipes, to withstand thermal expansion | It is recommended to evaluate if it is necessary to place flexible sections in the pipes, to withstand thermal expansion | ||
: The estimated elongation for these tubes sizes is really low, it can be supported by leaving clearances in the perforations. | |||
: --[[User:Inddigital|Inddigital]] ([[User talk:Inddigital|talk]]) 02:46, 25 January 2023 (CET) | |||
== Part number 1.05 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 23:54, 12 January 2023 (CEST) == | == Part number 1.05 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 23:54, 12 January 2023 (CEST) == | ||
In this sheet, the capture of solar energy can be optimized, simply with a coating of black paint, this detail is not observed in the project | In this sheet, the capture of solar energy can be optimized, simply with a coating of black paint, this detail is not observed in the project | ||
: Copied, it will be added in the next version of the plans | |||
: --[[User:Inddigital|Inddigital]] ([[User talk:Inddigital|talk]]) 02:46, 25 January 2023 (CET) | |||
== Part number 3.05 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 23:56, 12 January 2023 (CEST) == | == Part number 3.05 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 23:56, 12 January 2023 (CEST) == | ||
Here you can include a relief valve so that it only works to release the excess pressure and this access is not all the time losing heat from the tank | Here you can include a relief valve so that it only works to release the excess pressure and this access is not all the time losing heat from the tank | ||
: This would make the project more expensive, in addition, it is not expected that so much heat will escape through that hole, in any case a U curve can be added for a future version of the plans | |||
: --[[User:Inddigital|Inddigital]] ([[User talk:Inddigital|talk]]) 02:45, 25 January 2023 (CET) | |||
== Part number 3.02 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 23:58, 12 January 2023 (CEST) == | == Part number 3.02 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 23:58, 12 January 2023 (CEST) == | ||
Please include a commercial reference | Please include a commercial reference | ||
: https://www.amazon.com/-/es/V%C3%A1lvula-flotante-pulgadas-tanque-exterior/dp/B012S4F258 | |||
: You must place a hose or tube at the water outlet of this valve, to guarantee that the cold water enters through the bottom of the tank | |||
: --[[User:Inddigital|Inddigital]] ([[User talk:Inddigital|talk]]) 02:48, 25 January 2023 (CET) | |||
== Part number 2.15 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 00:00, 13 January 2023 (CEST) == | == Part number 2.15 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 00:00, 13 January 2023 (CEST) == | ||
Indicate the means of joining these plates to the lid sheet, ...riveting? | Indicate the means of joining these plates to the lid sheet, ...riveting? | ||
: Correct, this union is riveted, I will include it in a future delivery of the plans | |||
: --[[User:Inddigital|Inddigital]] ([[User talk:Inddigital|talk]]) 02:48, 25 January 2023 (CET) | |||
== Part number 1.00 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 00:02, 13 January 2023 (CEST) == | == Part number 1.00 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 00:02, 13 January 2023 (CEST) == | ||
The configuration of the tubes in the manifold makes it difficult for them to be threaded, it is recommended to use accessories to glue | The configuration of the tubes in the manifold makes it difficult for them to be threaded, it is recommended to use accessories to glue | ||
: Copied, it will be added in the next version of the plans | |||
: --[[User:Inddigital|Inddigital]] ([[User talk:Inddigital|talk]]) 02:53, 25 January 2023 (CET) | |||
== Part number 1.00 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 00:02, 13 January 2023 (CEST) == | == Part number 1.00 -- [[User:Xtech2020_review|Xtech2020_review]] ([[User talk:Xtech2020_review|talk]]) 00:02, 13 January 2023 (CEST) == | ||
It is recommended to include a rubber or silicone in the contact of the glass with the metal, this can only be indicated | It is recommended to include a rubber or silicone in the contact of the glass with the metal, this can only be indicated | ||
: Copied, it will be added in the next version of the plans | |||
: --[[User:Inddigital|Inddigital]] ([[User talk:Inddigital|talk]]) 02:53, 25 January 2023 (CET) |
Revision as of 02:52, 25 January 2023
Development and documentation - Technical solutions -- Inddigital (talk) 19:31, 23 January 2023 (CET)
- Parallel Tubes: preferable system
- Zigzag tubes: Proven system in commercial equipment but requires experience and additional equipment for bending
- Parallel Plates: Requires the fluid to develop enough pressure to deform the metal plates
- Copper: more expensive
- PVC: less heat transfer at the beginning, but a good working regime is reached in a short time
- Steel and galvanized iron in contact with water: more expensive than PVC piping
- A single circuit (mixed flow heat exchanger): Preferable, the utilization network can work by gravity
- Two circuits (coil heat exchanger): Requires pressurizing the network
-- Xtech2020_review (talk) 23:50, 12 January 2023 (CEST)
The perforations are missing in the insulating walls for the pipes to pass through, although it is not a critical detail, this can be quickly deduced during manufacturing
- Copied, it will be added in the next version of the plans
- --Inddigital (talk) 02:45, 25 January 2023 (CET)
Part number 4.00 -- Xtech2020_review (talk) 23:52, 12 January 2023 (CEST)
It is recommended to evaluate if it is necessary to place flexible sections in the pipes, to withstand thermal expansion
- The estimated elongation for these tubes sizes is really low, it can be supported by leaving clearances in the perforations.
- --Inddigital (talk) 02:46, 25 January 2023 (CET)
Part number 1.05 -- Xtech2020_review (talk) 23:54, 12 January 2023 (CEST)
In this sheet, the capture of solar energy can be optimized, simply with a coating of black paint, this detail is not observed in the project
- Copied, it will be added in the next version of the plans
- --Inddigital (talk) 02:46, 25 January 2023 (CET)
Part number 3.05 -- Xtech2020_review (talk) 23:56, 12 January 2023 (CEST)
Here you can include a relief valve so that it only works to release the excess pressure and this access is not all the time losing heat from the tank
- This would make the project more expensive, in addition, it is not expected that so much heat will escape through that hole, in any case a U curve can be added for a future version of the plans
- --Inddigital (talk) 02:45, 25 January 2023 (CET)
Part number 3.02 -- Xtech2020_review (talk) 23:58, 12 January 2023 (CEST)
Please include a commercial reference
- https://www.amazon.com/-/es/V%C3%A1lvula-flotante-pulgadas-tanque-exterior/dp/B012S4F258
- You must place a hose or tube at the water outlet of this valve, to guarantee that the cold water enters through the bottom of the tank
- --Inddigital (talk) 02:48, 25 January 2023 (CET)
Part number 2.15 -- Xtech2020_review (talk) 00:00, 13 January 2023 (CEST)
Indicate the means of joining these plates to the lid sheet, ...riveting?
- Correct, this union is riveted, I will include it in a future delivery of the plans
- --Inddigital (talk) 02:48, 25 January 2023 (CET)
Part number 1.00 -- Xtech2020_review (talk) 00:02, 13 January 2023 (CEST)
The configuration of the tubes in the manifold makes it difficult for them to be threaded, it is recommended to use accessories to glue
- Copied, it will be added in the next version of the plans
- --Inddigital (talk) 02:53, 25 January 2023 (CET)
Part number 1.00 -- Xtech2020_review (talk) 00:02, 13 January 2023 (CEST)
It is recommended to include a rubber or silicone in the contact of the glass with the metal, this can only be indicated
- Copied, it will be added in the next version of the plans
- --Inddigital (talk) 02:53, 25 January 2023 (CET)