Difference between revisions of "Pipe Bending Machine"
Inddigital (talk | contribs) |
Inddigital (talk | contribs) |
||
(6 intermediate revisions by 5 users not shown) | |||
Line 1: | Line 1: | ||
{{Projekt | {{Projekt | ||
|Images={{ProjektImages | |Images={{ProjektImages | ||
|projectimage=Pipe Bending Machine.png | |||
}}{{ProjektImages | |||
|projectimage=Oseg pbm img02.jpg | |projectimage=Oseg pbm img02.jpg | ||
}}{{ProjektImages | }}{{ProjektImages | ||
Line 28: | Line 30: | ||
|projectnameDE=Rohrbiegemaschine | |projectnameDE=Rohrbiegemaschine | ||
|kewords=metalworking, bending, pipe, tube, machine, elbow, thickness, material, metal, diy, abatec | |kewords=metalworking, bending, pipe, tube, machine, elbow, thickness, material, metal, diy, abatec | ||
|firstin=https:// | |firstin=https://www.youtube.com/watch?v=iYX-in1RDys | ||
|trans_status=WT | |trans_status=WT | ||
|desc=<p>Detailed drawings for building a tube bender</p> | |desc=<p>Detailed drawings for building a tube bender</p> | ||
Line 36: | Line 38: | ||
|organization=ApT | |organization=ApT | ||
|project_status=active | |project_status=active | ||
|design_files_pub=yes | |design_files_pub=yes | ||
|cad_files_editable=yes | |||
|mechanical_licence=CCBYSA40 | |mechanical_licence=CCBYSA40 | ||
|electronic_files_pub=no | |electronic_files_pub=no | ||
Line 65: | Line 67: | ||
|cmpfile2=Oseg pbm STEP.zip | |cmpfile2=Oseg pbm STEP.zip | ||
}}{{ProjektComponent | }}{{ProjektComponent | ||
|cmptitle= | |cmptitle=Attestation | ||
|cmpimage= | |cmpimage=Attestation Pipe Bending Machine.jpg | ||
|cmpfile1= | |cmpimg=The project Pipe Bending Machine was reviewed by two reviewers from the OHO team. The review consisted of the following components: | ||
1. Completeness check: Checks if all required documents have been submitted. | |||
2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. | |||
2.1 Bill of materials | |||
- Are all parts and assemblies covered? | |||
- Are all quantities correct? | |||
- Are all required material specifications available? | |||
- Are all specifications for purchased parts and standard parts complete? | |||
3.2 Technical drawings | |||
- Are all the required views available? | |||
- Are all required dimensional data available? | |||
4.1 Suggestions for improvement | |||
Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers | |||
Permanent Link: https://en.oho.wiki/index.php?title=Pipe_Bending_Machine&oldid=43459 | |||
|cmpfile1=Attestation Pipe Bending Machine.pdf | |||
}} | }} | ||
|Materials={{ProjektMaterials | |Materials={{ProjektMaterials | ||
Line 75: | Line 98: | ||
|matdrawingsheet=A1 | |matdrawingsheet=A1 | ||
|matpdffile=Oseg pbm A1-PIPE-BENDING-MACHINE.pdf | |matpdffile=Oseg pbm A1-PIPE-BENDING-MACHINE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 82: | Line 106: | ||
|matdrawingsheet=A2 | |matdrawingsheet=A2 | ||
|matpdffile=Oseg pbm A2 PIPE BENDING MACHINE.pdf | |matpdffile=Oseg pbm A2 PIPE BENDING MACHINE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 89: | Line 114: | ||
|matdrawingsheet=B1 | |matdrawingsheet=B1 | ||
|matpdffile=Oseg pbm B1-parts-list-pipe-binding-machine.pdf | |matpdffile=Oseg pbm B1-parts-list-pipe-binding-machine.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 96: | Line 122: | ||
|matdrawingsheet=1 | |matdrawingsheet=1 | ||
|matpdffile=Oseg pbm 1.0-SUB-PIPE-BENDING-MACHINE-1.pdf | |matpdffile=Oseg pbm 1.0-SUB-PIPE-BENDING-MACHINE-1.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 106: | Line 133: | ||
|matspec=FRAME, Steel C45 | |matspec=FRAME, Steel C45 | ||
|matpdffile=Oseg pbm 1.1-FRAME.pdf | |matpdffile=Oseg pbm 1.1-FRAME.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 116: | Line 144: | ||
|matspec=MAIN PIN, Steel C45 | |matspec=MAIN PIN, Steel C45 | ||
|matpdffile=Oseg pbm 1.2-MAIN-PIN.pdf | |matpdffile=Oseg pbm 1.2-MAIN-PIN.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 126: | Line 155: | ||
|matspec=STIFFENER, Steel C45 | |matspec=STIFFENER, Steel C45 | ||
|matpdffile=Oseg pbm 1.3-STIFFENER.pdf | |matpdffile=Oseg pbm 1.3-STIFFENER.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 136: | Line 166: | ||
|matspec=FORMER STOP, Steel C45 | |matspec=FORMER STOP, Steel C45 | ||
|matpdffile=Oseg pbm 1.4-FORMER-STOP.pdf | |matpdffile=Oseg pbm 1.4-FORMER-STOP.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 144: | Line 175: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=Pin - Cotter | |matspec=Pin - Cotter | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 151: | Line 183: | ||
|matdrawingsheet=2 | |matdrawingsheet=2 | ||
|matpdffile=Oseg pbm 2.0-SUB-PIPE-BENDING-MACHINE-2.pdf | |matpdffile=Oseg pbm 2.0-SUB-PIPE-BENDING-MACHINE-2.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 161: | Line 194: | ||
|matspec=FOOT, Steel C45 | |matspec=FOOT, Steel C45 | ||
|matpdffile=Oseg pbm 2.1-FOOT.pdf | |matpdffile=Oseg pbm 2.1-FOOT.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 171: | Line 205: | ||
|matspec=SUPPORT LEG, Steel C45 | |matspec=SUPPORT LEG, Steel C45 | ||
|matpdffile=Oseg pbm 2.2-SUPPORT-LEG.pdf | |matpdffile=Oseg pbm 2.2-SUPPORT-LEG.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 181: | Line 216: | ||
|matspec=MAIN LEG, Steel C45 | |matspec=MAIN LEG, Steel C45 | ||
|matpdffile=Oseg pbm 2.3-MAIN-LEG.pdf | |matpdffile=Oseg pbm 2.3-MAIN-LEG.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 189: | Line 225: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=Metric Formed Hex Screw - Formed Hex Screw - Metric (2) | |matspec=Metric Formed Hex Screw - Formed Hex Screw - Metric (2) | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 197: | Line 234: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=Hex Jam Nut | |matspec=Hex Jam Nut | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 204: | Line 242: | ||
|matdrawingsheet=3 | |matdrawingsheet=3 | ||
|matpdffile=Oseg pbm 3.0-SUB-PIPE-BENDING-MACHINE-3.pdf | |matpdffile=Oseg pbm 3.0-SUB-PIPE-BENDING-MACHINE-3.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 214: | Line 253: | ||
|matspec=HANDLE, Steel C45 | |matspec=HANDLE, Steel C45 | ||
|matpdffile=Oseg pbm 3.1-HANDLE.pdf | |matpdffile=Oseg pbm 3.1-HANDLE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 224: | Line 264: | ||
|matspec=FORMER SPACER, Steel C45 | |matspec=FORMER SPACER, Steel C45 | ||
|matpdffile=Oseg pbm 3.2-FORMER-SPACER.pdf | |matpdffile=Oseg pbm 3.2-FORMER-SPACER.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 234: | Line 275: | ||
|matspec=HANDLE ARM, Steel C45 | |matspec=HANDLE ARM, Steel C45 | ||
|matpdffile=Oseg pbm 3.3-HANDLE-ARM.pdf | |matpdffile=Oseg pbm 3.3-HANDLE-ARM.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 244: | Line 286: | ||
|matspec=HANDLE SPACER, Steel C45 | |matspec=HANDLE SPACER, Steel C45 | ||
|matpdffile=Oseg pbm 3.4-HANDLE-SPACER.pdf | |matpdffile=Oseg pbm 3.4-HANDLE-SPACER.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 254: | Line 297: | ||
|matspec=ROLLER, Steel C45 | |matspec=ROLLER, Steel C45 | ||
|matpdffile=Oseg pbm 3.5-ROLLER.pdf | |matpdffile=Oseg pbm 3.5-ROLLER.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 261: | Line 305: | ||
|matdrawingsheet=4 | |matdrawingsheet=4 | ||
|matpdffile=Oseg pbm 4.0-SUB-PIPE-BENDING-MACHINE-4.pdf | |matpdffile=Oseg pbm 4.0-SUB-PIPE-BENDING-MACHINE-4.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 271: | Line 316: | ||
|matspec=ROLLER PIN, Steel C45 | |matspec=ROLLER PIN, Steel C45 | ||
|matpdffile=Oseg pbm 4.1-ROLLER-PIN.pdf | |matpdffile=Oseg pbm 4.1-ROLLER-PIN.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 281: | Line 327: | ||
|matspec=PIN HANDLE, Steel C45 | |matspec=PIN HANDLE, Steel C45 | ||
|matpdffile=Oseg pbm 4.2-PIN-HANDLE.pdf | |matpdffile=Oseg pbm 4.2-PIN-HANDLE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 288: | Line 335: | ||
|matdrawingsheet=5 | |matdrawingsheet=5 | ||
|matpdffile=Oseg pbm 5.0-SUB-PIPE-BENDING-MACHINE-5.pdf | |matpdffile=Oseg pbm 5.0-SUB-PIPE-BENDING-MACHINE-5.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 298: | Line 346: | ||
|matspec=STOP TUBE, Steel C45 | |matspec=STOP TUBE, Steel C45 | ||
|matpdffile=Oseg pbm 5.1-STOP-TUBE.pdf | |matpdffile=Oseg pbm 5.1-STOP-TUBE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 308: | Line 357: | ||
|matspec=STOP ANGLE, Steel C45 | |matspec=STOP ANGLE, Steel C45 | ||
|matpdffile=Oseg pbm 5.2-STOP-ANGLE.pdf | |matpdffile=Oseg pbm 5.2-STOP-ANGLE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 315: | Line 365: | ||
|matdrawingsheet=6 | |matdrawingsheet=6 | ||
|matpdffile=Oseg pbm 6.0-SUB-PIPE-BENDING-MACHINE-6.pdf | |matpdffile=Oseg pbm 6.0-SUB-PIPE-BENDING-MACHINE-6.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 325: | Line 376: | ||
|matspec=GUIDE ANGLE, Steel C45 | |matspec=GUIDE ANGLE, Steel C45 | ||
|matpdffile=Oseg pbm 6.1-GUIDE-ANGLE.pdf | |matpdffile=Oseg pbm 6.1-GUIDE-ANGLE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 335: | Line 387: | ||
|matspec=GUIDE BASE, Steel C45 | |matspec=GUIDE BASE, Steel C45 | ||
|matpdffile=Oseg pbm 6.2-GUIDE-BASE.pdf | |matpdffile=Oseg pbm 6.2-GUIDE-BASE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 342: | Line 395: | ||
|matdrawingsheet=7 | |matdrawingsheet=7 | ||
|matpdffile=Oseg pbm 7.0-SUB-PIPE-BENDING-MACHINE-7.pdf | |matpdffile=Oseg pbm 7.0-SUB-PIPE-BENDING-MACHINE-7.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 352: | Line 406: | ||
|matspec=FORMER SIDE, Steel C45 | |matspec=FORMER SIDE, Steel C45 | ||
|matpdffile=Oseg pbm 7.1-FORMER-BASE.pdf | |matpdffile=Oseg pbm 7.1-FORMER-BASE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 362: | Line 417: | ||
|matspec=FORMER SIDE, Steel C45 | |matspec=FORMER SIDE, Steel C45 | ||
|matpdffile=Oseg pbm 7.2-FORMER-SIDE.pdf | |matpdffile=Oseg pbm 7.2-FORMER-SIDE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 372: | Line 428: | ||
|matspec=SPACER TUBE, Steel C45 | |matspec=SPACER TUBE, Steel C45 | ||
|matpdffile=Oseg pbm 7.3-SPACER-TUBE.pdf | |matpdffile=Oseg pbm 7.3-SPACER-TUBE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 382: | Line 439: | ||
|matspec=PIN LINK, Steel C45 | |matspec=PIN LINK, Steel C45 | ||
|matpdffile=Oseg pbm 7.4-PIN-LINK.pdf | |matpdffile=Oseg pbm 7.4-PIN-LINK.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
Line 390: | Line 448: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=Hex Bolt | |matspec=Hex Bolt | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |status_rev_2=approved | ||
}} | }} | ||
|certificate_requested=No | |certificate_requested=No | ||
|certificate_status= | |certificate_status=approved | ||
|reviewer1=Xtech2020 review | |reviewer1=Xtech2020 review | ||
|reviewer2=Thehunter | |reviewer2=Thehunter | ||
}} | }} |
Latest revision as of 17:08, 14 March 2022
Pipe Bending Machine Basic Data Category: Tube benders URL (first publication): https://www.youtube.com/watch?v=iYX-in1RDys Keywords: metalworking, bending, pipe, tube, machine, elbow, thickness, material, metal, diy, abatec License: CC BY-SA 4.0 Organization: ApT Project status: Active Certification status: Approved Technical documentation
Contains PDF-drawings: Yes CAD files are editable: Yes Assembly instructions are published: No Bill of materials is published: Yes
yes yes
|
Description
Detailed drawings for building a tube bender
Project published under CC-BY-SA 4.0 license
Technical documentation
PDF Plans | |
Files: |
CAD Files - part 1 | |
Files: |
CAD Files - part 2 | |
Files: |
Attestation | |
The project Pipe Bending Machine was reviewed by two reviewers from the OHO team. The review consisted of the following components:
1. Completeness check: Checks if all required documents have been submitted. 2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. 2.1 Bill of materials - Are all parts and assemblies covered? - Are all quantities correct? - Are all required material specifications available? - Are all specifications for purchased parts and standard parts complete? 3.2 Technical drawings - Are all the required views available? - Are all required dimensional data available? 4.1 Suggestions for improvement Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers Permanent Link: https://en.oho.wiki/index.php?title=Pipe_Bending_Machine&oldid=43459 | |
Files: |
+ General Reviews
Parts list
Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
---|---|---|---|---|---|---|---|---|
A1 | 1 | PIPE BENDING MACHINE | A1 |
REV1: Approved |
||||
A2 | 1 | PIPE BENDING MACHINE | A2 |
REV1: Approved |
||||
B1 | 1 | PARTS LITS | B1 |
REV1: Approved |
||||
1 | 1 | SUB-PIPE BENDING MACHINE 1 | 1 |
REV1: Approved |
||||
1.1 | 1 | FRAME | 1.1 | Production | FRAME, Steel C45 |
REV1: Approved |
||
1.2 | 1 | MAIN PIN | 1.2 | Production | MAIN PIN, Steel C45 |
REV1: Approved |
||
1.3 | 1 | STIFFENER | 1.3 | Production | STIFFENER, Steel C45 |
REV1: Approved |
||
1.4 | 1 | FORMER STOP | 1.4 | Production | FORMER STOP, Steel C45 |
REV1: Approved |
||
1.5 | 2 | SAE J487a - 3/32 x 1 Extended Prong Square Cut Type | 1.5 | Standard | Pin - Cotter |
REV1: Approved |
||
2 | 1 | SUB-PIPE BENDING MACHINE 2 | 2 |
REV1: Approved |
||||
2.1 | 1 | FOOT | 2.1 | Production | FOOT, Steel C45 |
REV1: Approved |
||
2.2 | 1 | SUPPORT LEG | 2.2 | Production | SUPPORT LEG, Steel C45 |
REV1: Approved |
||
2.3 | 1 | MAIN LEG | 2.3 | Production | MAIN LEG, Steel C45 |
REV1: Approved |
||
2.4 | 1 | ANSI B18.2.3.2M - M10 x 1,5 | 2.4 | Standard | Metric Formed Hex Screw - Formed Hex Screw - Metric (2) |
REV1: Approved |
||
2.5 | 6 | ANSI B18.2.4.5M - M10 x 1.5 | 2.5 | Standard | Hex Jam Nut |
REV1: Approved |
||
3 | 1 | SUB-PIPE BENDING MACHINE 3 | 3 |
REV1: Approved |
||||
3.1 | 1 | HANDLE | 3.1 | Production | HANDLE, Steel C45 |
REV1: Approved |
||
3.2 | 1 | FORMER SPACER | 3.2 | Production | FORMER SPACER, Steel C45 |
REV1: Approved |
||
3.3 | 1 | HANDLE ARM | 3.3 | Production | HANDLE ARM, Steel C45 |
REV1: Approved |
||
3.4 | 1 | HANDLE SPACER | 3.4 | Production | HANDLE SPACER, Steel C45 |
REV1: Approved |
||
3.5 | 1 | ROLLER | 3.5 | Production | ROLLER, Steel C45 |
REV1: Approved |
||
4 | 1 | SUB-PIPE BENDING MACHINE 4 | 4 |
REV1: Approved |
||||
4.1 | 1 | ROLLER PIN | 4.1 | Production | ROLLER PIN, Steel C45 |
REV1: Approved |
||
4.2 | 1 | PIN HANDLE | 4.2 | Production | PIN HANDLE, Steel C45 |
REV1: Approved |
||
5 | 1 | SUB-PIPE BENDING MACHINE 5 | 5 |
REV1: Approved |
||||
5.1 | 1 | STOP TUBE | 5.1 | Production | STOP TUBE, Steel C45 |
REV1: Approved |
||
5.2 | 1 | STOP ANGLE | 5.2 | Production | STOP ANGLE, Steel C45 |
REV1: Approved |
||
6 | 1 | SUB-PIPE BENDING MACHINE 6 | 6 |
REV1: Approved |
||||
6.1 | 1 | GUIDE ANGLE | 6.1 | Production | GUIDE ANGLE, Steel C45 |
REV1: Approved |
||
6.2 | 1 | GUIDE BASE | 6.2 | Production | GUIDE BASE, Steel C45 |
REV1: Approved |
||
7 | 1 | SUB-PIPE BENDING MACHINE 7 | 7 |
REV1: Approved |
||||
7.1 | 1 | FORMER BASE | 7.1 | Production | FORMER SIDE, Steel C45 |
REV1: Approved |
||
7.2 | 1 | FORMER SIDE | 7.2 | Production | FORMER SIDE, Steel C45 |
REV1: Approved |
||
7.3 | 1 | SPACER TUBE | 7.3 | Production | SPACER TUBE, Steel C45 |
REV1: Approved |
||
7.4 | 1 | PIN LINK | 7.4 | Production | PIN LINK, Steel C45 |
REV1: Approved |
||
7.5 | 5 | ANSI B18.2.3.5M - M10 x 1,5 x 45 | 7.5 | Standard | Hex Bolt |
REV1: Approved |
||