Difference between revisions of "Corn mill"
Inddigital (talk | contribs) |
Inddigital (talk | contribs) ((by SublimeText.Mediawiker)) |
||
(44 intermediate revisions by 6 users not shown) | |||
Line 1: | Line 1: | ||
{{ | {{Projekt2 | ||
|Images={{ProjektImages | |Images=cm-My homemade corn mill 10-33 screenshot.png | ||
{{ProjektImages | |||
|projectimage= | |||
}} | |||
{{ProjektImages | |||
|projectimage=Maxresdefault.jpg | |||
}} | |||
{{ProjektImages | |||
|projectimage=Cm-0 3.png | |projectimage=Cm-0 3.png | ||
}}{{ProjektImages | }} | ||
|projectimage= | {{ProjektImages | ||
}}{{ProjektImages | |projectimage=cm-Corn_mill_screenshots_new_Page5_Image1.jpg | ||
}} | |||
{{ProjektImages | |||
|projectimage=cm-Corn_mill_screenshots_new_Page13_Image2.jpg | |||
}} | |||
{{ProjektImages | |||
|projectimage=Cm-part-list.png | |projectimage=Cm-part-list.png | ||
}}{{ProjektImages | }} | ||
{{ProjektImages | |||
|projectimage=Cm-4.png | |projectimage=Cm-4.png | ||
}}{{ProjektImages | }} | ||
{{ProjektImages | |||
|projectimage=Cm-3.png | |projectimage=Cm-3.png | ||
}}{{ProjektImages | }} | ||
{{ProjektImages | |||
|projectimage=Cm-2 2.png | |projectimage=Cm-2 2.png | ||
}}{{ProjektImages | }} | ||
{{ProjektImages | |||
|projectimage=Cm-2.png | |projectimage=Cm-2.png | ||
}}{{ProjektImages | }} | ||
{{ProjektImages | |||
|projectimage=Cm-1 2.png | |projectimage=Cm-1 2.png | ||
}}{{ProjektImages | }} | ||
{{ProjektImages | |||
|projectimage=Cm-1.png | |projectimage=Cm-1.png | ||
}} | }} | ||
Line 23: | Line 41: | ||
|projectnameES=Molino de maíz | |projectnameES=Molino de maíz | ||
|projectnameDE=Maismühle | |projectnameDE=Maismühle | ||
|kewords=corn mill grinder flour homemade diesel engine diy | |kewords=corn mill, grinder, flour homemade, diesel engine diy | ||
|firstin=https://www.youtube.com/watch?v= | |firstin=https://www.youtube.com/watch?v=pHjd-Ir2YfI | ||
|trans_status=WT | |trans_status=WT | ||
|licence=CCBYSA | |licence=CCBYSA | ||
|typeproject=Youtube | |typeproject=Youtube | ||
|project_status=active | |project_status=active | ||
|design_files_pub=yes | |design_files_pub=yes | ||
|cad_files_editable=yes | |cad_files_editable=yes | ||
Line 44: | Line 59: | ||
|versioning_system=no | |versioning_system=no | ||
|contains_pdf_drawings=yes | |contains_pdf_drawings=yes | ||
|technology_readyness_level= | |technology_readyness_level=6 | ||
|TechDoc={{ | |Desc= | ||
|cmptitle= | {{ProjektComponent2 | ||
|cmpimage= | |cmptitle=Description | ||
|cmpfile1= | |cmpimage=Corn mill foto 2.jpg | ||
}}{{ | |cmpimg= | ||
|cmptitle=CAD | The diesel-powered hammer mill for corn processing is a robust and portable machine, powered by a reliable diesel engine, designed through reverse engineering from a home video. It features a simple yet effective design with a metal frame, hammers, and a screen for grinding corn. Easy to operate and maintain, it uses readily available materials and parts, making it cost-effective. The reverse engineering process exemplifies human ingenuity and problem-solving skills, creating a practical agricultural tool for rural communities. | ||
|cmpimage= | |||
Project development: Reverse engineering without adviser (B1, P1) | |||
<!-- Reference: https://www.youtube.com/watch?v=anW5-WbnmtA&feature=emb_imp_woyt --> | |||
}} | |||
<div style="margin:20px"></div> | |||
{{ProjektComponent2 | |||
|cmptitle= Technical data | |||
|cmpimg= | |||
<div> | |||
<table width="100%" style="border: solid 1px !important;"> | |||
<tr style="visibility: collapse;"> | |||
<td width='50%'></td> | |||
<td width='50%'></td> | |||
</tr> | |||
<tr style="border: solid 1px !important;"> | |||
<th style="display: table-cell;"> Feature | |||
</th> | |||
<th style="display: table-cell;"> Detail | |||
</th> | |||
</tr> | |||
<tr> | |||
<td style="display: table-cell;"> Shaft diameter | |||
</td> | |||
<td style="display: table-cell;"> 20mm | |||
</td> | |||
</tr> | |||
<tr> | |||
<td style="display: table-cell;"> Hopper size | |||
</td> | |||
<td style="display: table-cell;"> 0.6 m (L) x 0.2 m (W) x 0.2 m (H) | |||
</td> | |||
</tr> | |||
<tr> | |||
<td style="display: table-cell;"> Grinding capacity | |||
</td> | |||
<td style="display: table-cell;"> 30-60 kg/hr (estimated according to the [[#Tests, practical applications|test]] carried out) | |||
</td> | |||
</tr> | |||
</table> | |||
</div> | |||
}} | |||
|TechDoc= | |||
{{ProjektComponent2 | |||
|cmptitle=PDF plans | |||
|cmpimage=oseg_cm_corn-mill_1.01_p23.jpg | |||
|cmpfile1=Oseg cm corn-mill 1.01.pdf | |||
}} | |||
{{ProjektComponent2 | |||
|cmptitle=CAD files | |||
|cmpimage=oseg_cm_3d1.jpg | |||
|cmpfile1=CAD-files.zip | |cmpfile1=CAD-files.zip | ||
}}{{ | |cmpfile2=Corn-mil STP-file.zip | ||
}} | |||
{{ProjektComponent2 | |||
|cmptitle=Reverse engineering of the corn mill | |cmptitle=Reverse engineering of the corn mill | ||
|cmpimage=cm_Tests_Sketchup_match_photo_Page4_Image1.jpg | |||
|cmpimg= | |||
A home video was used to design the corn mill using reverse engineering through perspective correction by photo match. This involved analyzing the video footage and extracting measurements and dimensions to create a 3D model of the corn mill. The video provided a unique perspective of the corn mill and allowed for an accurate design to be created. | |||
The reverse engineering process involved analyzing the perspective of the video and correcting any distortions caused by the camera angle. The resulting corn mill design can be efficient and cost-effective, with sturdy construction and customizable features. | |||
|cmpfile1=corn mill screenshots new.pdf | |cmpfile1=corn mill screenshots new.pdf | ||
|cmpfile2=Tests Sketchup match photo.pdf | |cmpfile2=Tests Sketchup match photo.pdf | ||
}} | |||
<div style="margin:20px"></div> | |||
{{ProjektComponent2 | |||
|cmptitle=Assembly instructions | |||
<!-- |cmpimage=oho-spe-test1.png --> | |||
|cmpimg= | |||
Here are some plans with the assembly sets and pieces. | |||
<div class="mw-collapsible" id="mw-customcollapsible-div1" data-origID="mw-customcollapsible-div1"> | |||
<div style="text-align:left;"> | |||
<i class="mw-customtoggle-div1" style="color:#1b599a;">Zoom in</i> | |||
</div> | |||
<div class="res-img col-auto col-sm-auto col-md-auto col-lg-5 col-xl-5"> | |||
<div style="border: solid;">[[File:Cm-0_3.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-4.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-3.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-2_2.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-2.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-1_2.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-1.png]]</div> | |||
</div> | |||
</div> | |||
<div class="mw-collapsible mw-collapsed" id="mw-customcollapsible-div1" data-origID="mw-customcollapsible-div1"> | |||
<div style="text-align:left;"> | |||
<i class="mw-customtoggle-div1" style="color:#1b599a;">Zoom out</i> | |||
</div> | |||
<div class="res-img" style="width: 800px"> | |||
<div style="border: solid;">[[File:Cm-0_3.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-4.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-3.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-2_2.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-2.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-1_2.png]]</div> | |||
<div style="margin:20px"></div> | |||
<div style="border: solid;">[[File:Cm-1.png]]</div> | |||
</div> | |||
</div> | |||
On the original developer's video, you can see [https://www.youtube.com/watch?v=anW5-WbnmtA some explanations] about the parts of the corn mill | |||
}} | |||
<div style="margin:20px"></div> | |||
{{ProjektComponent2 | |||
|cmptitle=Tests, practical applications | |||
|cmpimage=cm-Corn_mill_screenshots_new_Page1_Image2.jpg | |||
|cmpimg= | |||
It can be seen that the equipment is put to the test, obtaining about 1 kg of product, for 2 minutes, watch [https://youtu.be/anW5-WbnmtA?t=407 this moment of the video]. | |||
}} | }} | ||
|Materials={{ProjektMaterials | |Materials={{ProjektMaterials | ||
Line 63: | Line 190: | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=A005.pdf | |matpdffile=A005.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
|status_rev_2= | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=1 | |matpartnumber=1 | ||
Line 71: | Line 199: | ||
|matdesc=Base Frame / Grundrahmen / Marco Base | |matdesc=Base Frame / Grundrahmen / Marco Base | ||
|matparttype=production | |matparttype=production | ||
|matpdffile= | |matpdffile=Oseg cm 1.0.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2= | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=1.1 | |matpartnumber=1.1 | ||
Line 81: | Line 210: | ||
|matdrawingsheet=002 | |matdrawingsheet=002 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile= | |matpdffile=Oseg cm 1.1.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
|status_rev_2= | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=1.2 | |matpartnumber=1.2 | ||
Line 93: | Line 223: | ||
|matpdffile=001.pdf | |matpdffile=001.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2= | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=1.3 | |matpartnumber=1.3 | ||
Line 103: | Line 234: | ||
|matpdffile=004.pdf | |matpdffile=004.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=1.4 | |matpartnumber=1.4 | ||
Line 112: | Line 245: | ||
|matpdffile=003.pdf | |matpdffile=003.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=2 | |matpartnumber=2 | ||
Line 118: | Line 253: | ||
|matdesc=Lower Funnel / Unterer Trichter / Tolva Inferior | |matdesc=Lower Funnel / Unterer Trichter / Tolva Inferior | ||
|matparttype=production | |matparttype=production | ||
|matpdffile= | |matpdffile=Oseg cm 2.0.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=2.1 | |matpartnumber=2.1 | ||
Line 129: | Line 266: | ||
|matpdffile=006.pdf | |matpdffile=006.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=2.2 | |matpartnumber=2.2 | ||
Line 138: | Line 277: | ||
|matpdffile=005.pdf | |matpdffile=005.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=2.3 | |matpartnumber=2.3 | ||
Line 147: | Line 288: | ||
|matpdffile=2.3.pdf | |matpdffile=2.3.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=2.4 | |matpartnumber=2.4 | ||
Line 153: | Line 296: | ||
|matpdffile=2.4.pdf | |matpdffile=2.4.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3 | |matpartnumber=3 | ||
Line 161: | Line 306: | ||
|matpdffile=dico polea.pdf | |matpdffile=dico polea.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.1 | |matpartnumber=3.1 | ||
Line 170: | Line 317: | ||
|matpdffile=3.1.pdf | |matpdffile=3.1.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.2 | |matpartnumber=3.2 | ||
Line 179: | Line 328: | ||
|matpdffile=014.pdf | |matpdffile=014.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.3 | |matpartnumber=3.3 | ||
Line 188: | Line 339: | ||
|matpdffile=011.pdf | |matpdffile=011.pdf | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.4 | |matpartnumber=3.4 | ||
Line 198: | Line 351: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.5 | |matpartnumber=3.5 | ||
Line 208: | Line 362: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.6 | |matpartnumber=3.6 | ||
Line 218: | Line 373: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.7 | |matpartnumber=3.7 | ||
Line 228: | Line 384: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.8 | |matpartnumber=3.8 | ||
Line 238: | Line 395: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.9 | |matpartnumber=3.9 | ||
Line 248: | Line 406: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4 | |matpartnumber=4 | ||
Line 255: | Line 414: | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=A004.pdf | |matpdffile=A004.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.1 | |matpartnumber=4.1 | ||
Line 266: | Line 427: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.2 | |matpartnumber=4.2 | ||
Line 276: | Line 438: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.3 | |matpartnumber=4.3 | ||
Line 286: | Line 449: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.4 | |matpartnumber=4.4 | ||
Line 296: | Line 460: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.5 | |matpartnumber=4.5 | ||
Line 306: | Line 471: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.6 | |matpartnumber=4.6 | ||
Line 316: | Line 482: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.7 | |matpartnumber=4.7 | ||
Line 326: | Line 493: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.8 | |matpartnumber=4.8 | ||
Line 336: | Line 504: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.9 | |matpartnumber=4.9 | ||
Line 345: | Line 514: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.10 | |matpartnumber=4.10 | ||
Line 355: | Line 525: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4.11 | |matpartnumber=4.11 | ||
Line 365: | Line 536: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=5 | |matpartnumber=5 | ||
Line 374: | Line 546: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=6 | |matpartnumber=6 | ||
Line 383: | Line 556: | ||
|status_rev_1=approved | |status_rev_1=approved | ||
|status_rev_2=approved | |status_rev_2=approved | ||
|status_rev_3=approved | |||
}} | }} | ||
|certificate_requested=No | |certificate_requested=No | ||
Line 388: | Line 562: | ||
|reviewer1=Aquilesmorillo | |reviewer1=Aquilesmorillo | ||
|reviewer2=Pomelo | |reviewer2=Pomelo | ||
|reviewer3=Thehunter | |||
}} | }} |
Latest revision as of 19:19, 20 April 2023
Project data
Category: Mills URL (first publication): https://www.youtube.com/watch?v=pHjd-Ir2YfI Keywords: corn mill, grinder, flour homemade, diesel engine diy License: CC BY-SA Project status: Active Certification status: In process
Contains PDF-drawings: Yes CAD files are editable: Yes Assembly instructions are published: Yes Bill of materials is published: Yes
no no
|
Project details
Description
The diesel-powered hammer mill for corn processing is a robust and portable machine, powered by a reliable diesel engine, designed through reverse engineering from a home video. It features a simple yet effective design with a metal frame, hammers, and a screen for grinding corn. Easy to operate and maintain, it uses readily available materials and parts, making it cost-effective. The reverse engineering process exemplifies human ingenuity and problem-solving skills, creating a practical agricultural tool for rural communities.
Project development: Reverse engineering without adviser (B1, P1)
Technical data
Feature | Detail |
---|---|
Shaft diameter | 20mm |
Hopper size | 0.6 m (L) x 0.2 m (W) x 0.2 m (H) |
Grinding capacity | 30-60 kg/hr (estimated according to the test carried out) |
Technical documentation
Reverse engineering of the corn mill
A home video was used to design the corn mill using reverse engineering through perspective correction by photo match. This involved analyzing the video footage and extracting measurements and dimensions to create a 3D model of the corn mill. The video provided a unique perspective of the corn mill and allowed for an accurate design to be created.
The reverse engineering process involved analyzing the perspective of the video and correcting any distortions caused by the camera angle. The resulting corn mill design can be efficient and cost-effective, with sturdy construction and customizable features.
Assembly instructions
Here are some plans with the assembly sets and pieces.
On the original developer's video, you can see some explanations about the parts of the corn mill
Tests, practical applications
It can be seen that the equipment is put to the test, obtaining about 1 kg of product, for 2 minutes, watch this moment of the video.
+ General Reviews
Reviews
Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
---|---|---|---|---|---|---|---|---|
0 | Corn mill / Mais Mühle / Molino de maíz | Production |
REV1: Approved |
|||||
1 | 1 | Base Frame / Grundrahmen / Marco Base | Production |
REV1: Approved |
||||
1.1 | 2 | Frame 2 / Rahmen 2 / Marco 2 | 002 | Production |
REV1: Approved |
|||
1.2 | 2 | Frame 1 / Rahmen 1 / Marco 1 | 001 | Production |
REV1: Approved |
|||
1.3 | 1 | Round Tube 1 1/8 / Rundrohr 1 1/8 / Tubo Redondo 1 1/8 | 004 | Production |
REV1: Approved |
|||
1.4 | 1 | Tube 1x1 / Rohr 1x1 / Tubo1x1 | 003 | Production |
REV1: Approved |
|||
2 | 1 | Lower Funnel / Unterer Trichter / Tolva Inferior | Production |
REV1: Approved |
||||
2.1 | 2 | Lower Funnel 1 / Unterer Trichter 1 / Tolva Inferior 1 | 006 | Production |
REV1: Approved |
|||
2.2 | 2 | Lower Funnel 2 / Unterer Trichter 2 / Tolva Inferior 2 | 005 | Production |
REV1: Approved |
|||
2.3 | 1 | Angle Base 1 / Winkelbasis 1 / Base Angulo 1 | A001 | Production |
REV1: Approved |
|||
2.4 | Angle Base 2 / Winkelbasis 2 / Base Angulo 2 | Production |
REV1: Approved |
|||||
3 | 1 | Pulley Disc / Riemenscheibe / Disco Polea | Production |
REV1: Approved |
||||
3.1 | 1 | Bush Tapered / Buchse / Bocina | 015 | Production |
REV1: Approved |
|||
3.2 | 5 | Disc / Scheibe / Disco Polea | 014 | Production |
REV1: Approved |
|||
3.3 | 5 | Bolt / Bolzen / Pasador | 011 | Production |
REV1: Approved |
|||
3.4 | 4 | Spacer / Distanzscheibe / Separador | 016 | Production |
REV1: Approved |
|||
3.5 | 8 | Hammer / / Martillo | 013 | Production |
REV1: Approved |
|||
3.6 | 2 | Housing Bearing / Gehaeuselager / Chumacera | Buy | 24200-20204 |
REV1: Approved |
|||
3.7 | 1 | Axis / Achse / Eje | 010 | Production |
REV1: Approved |
|||
3.8 | 1 | Pulley / Riemenscheibe / Polea | 009 | Production |
REV1: Approved |
|||
3.9 | 2 | Key / Schluessel / Chaveta | 012 | Production |
REV1: Approved |
|||
4 | 1 | Upper Hopper / Oberer Trichter / Tolba Superior | Production |
REV1: Approved |
||||
4.1 | 2 | Side Part Funnel 1 / Seitenteil Trichter 1 / Lateral Tolva 1 | 017 | Production |
REV1: Approved |
|||
4.2 | 1 | Side Part Funnel 18A / Seitenteil Trichter 18A / Lateral Tolva 18A | 018A | Production |
REV1: Approved |
|||
4.3 | 2 | Side Part Funnel 4 / Seitenteil Trichter 4 / Lateral Tolva 4 | 020 | Production |
REV1: Approved |
|||
4.4 | 2 | Side Part Funnel 3 / Seitenteil Trichter 3 / Lateral Tolva 3 | 021 | Production |
REV1: Approved |
|||
4.5 | 4 | Side Part Funnel 5 / Seitenteil Trichter 5 / Lateral Tolva 5 | 019 | Production |
REV1: Approved |
|||
4.6 | 1 | Side Part Funnel 6 / Seitenteil Trichter 6 / Lateral Tolva 6 | 024 | Production |
REV1: Approved |
|||
4.7 | 1 | Side Part Funnel 7 / Seitenteil Trichter 7 / Lateral Tolva 7 | 023 | Production |
REV1: Approved |
|||
4.8 | 1 | Side Part Funnel 8 / Seitenteil Trichter 8 / Lateral Tolva 8 | 022 | Production |
REV1: Approved |
|||
4.9 | 1 | Side Part Funnel 2A / Seitenteil Trichter 2A / Lateral Tolva 2A | 018 | Production |
REV1: Approved |
|||
4.10 | 1 | Gate / Tor / Compuerta | 026 | Production |
REV1: Approved |
|||
4.11 | 1 | Lever / Hebel / Palanca | 025 | Production |
REV1: Approved |
|||
5 | 1 | Hinge / Scharnier / Bisagra | Buy | 72-1-3635 |
REV1: Approved |
|||
6 | 1 | Closure / Verschluss / Cierre | Buy | 420091 |
REV1: Approved |
|||