Wind Mill Pump
|
Wind Mill Pump Basic Data Category: Savonius wind turbines URL (first publication): https://www.youtube.com/watch?v=DfHtDeaLkGg Keywords: savonius, rotor, cheap, blueprints, construction, wind turbine, vawt, Brace Research Institute, oil drum, diaphragm pump, water License: CC BY-SA 4.0 Organization: Brace Research Institute Project status: Active Certification status: Approved Technical documentation
Contains PDF-drawings: Yes CAD files are editable: Yes Assembly instructions are published: Yes Bill of materials is published: Yes
yes yes
|
Description
Plans and 3d models to build a DIY equipment to pump water using a Savonius turbine and a diaphragm pump.
Original design by Brace Research Institute, published under a CC-BY-SA 4.0 license.
This project was supported by the german Foundation E.ON Stiftung.
Technical documentation
PDF Plans | |
|
|
Files: | |
CAD Files | |
|
|
Files: | |
Attestation | |
|
The project Wind Mill Pump was reviewed by two reviewers from the OHO team. The review consisted of the following components:
1. Completeness check: Checks if all required documents have been submitted. 2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. 2.1 Bill of materials - Are all parts and assemblies covered? - Are all quantities correct? - Are all required material specifications available? - Are all specifications for purchased parts and standard parts complete? 3.2 Technical drawings - Are all the required views available? - Are all required dimensional data available? 4.1 Suggestions for improvement Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers Permanent Link: https://en.oho.wiki/index.php?title=Wind_Mill_Pump&oldid=44512 |
Files: | |
+ General Reviews 
Parts list
| Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
|---|---|---|---|---|---|---|---|---|
| A1 | wind mill pump | A1 |
REV1: Approved |
|
||||
| A2 | wind mill pump | A2 |
REV1: Approved |
|
||||
| B | Part list | B |
REV1: Approved |
|
||||
| 1 | The Rotor | 1 |
REV1: Approved |
|
||||
| 1.1 | 4 | 1/2 oil drum | 1.1 | Production | 200-litre drum 867 height x 584 diam |
REV1: Approved |
|
|
| 1.2 | 2 | plates plywood | 1.2 | Production | plywood |
REV1: Approved |
|
|
| 1.3 | 2 | flange support | 1.3 | Production | structural steel A36 |
REV1: Approved |
|
|
| 1.4 | 2 | rotor shaft | 1.4 | Production | steel C45 |
REV1: Approved |
|
|
| 2 | Frame | 2 |
REV1: Approved |
|
||||
| 2.1 | 2 | supporting laths 50x25x3000 | 2.1 | structural steel A36 |
REV1: Approved |
|
||
| 2.2 | 2 | supporting laths 50x25x1300 | 2.2 | structural steel A36 |
REV1: Approved |
|
||
| 2.3 | 1 | top adaptor | 2.3 | Production | steel C45 |
REV1: Approved |
|
|
| 2.4 | 1 | bottom adaptor | 2.4 | Production | steel C45 |
REV1: Approved |
|
|
| 2.5 | 2 | self alighing bearing | 2.5 | Standard | bearing 6205 - 25x56x15 |
REV1: Approved |
|
|
| 2.6 | 2 | bearing support | 2.6 | Production | steel C45 |
REV1: Approved |
|
|
| 2.7 | 2 | rectangular flancher | 2.7 | Production | steel C45 |
REV1: Approved |
|
|
| 2.8 | 3 | securing bolt | 2.8 | Standard | round head screw, galvanized steel |
REV1: Approved |
|
|
| 2.9 | 3 | securing nut | 2.9 | Standard | galvanized steel |
REV1: Approved |
|
|
| 3 | drive | 3 | Production |
REV1: Approved |
|
|||
| 3.1 | 1 | Excentric | 3.1 | Production | steel C45 |
REV1: Approved |
|
|
| 3.2 | horizontal connecting rod | 3.2 |
REV1: Approved |
|
||||
| 3.2.1 | connecting rod | 3.2.1 | Standard | connecting rod of a motorcycle or small car engine |
REV1: Approved |
|
||
| 3.2.2 | 2 | water pipe 1"x150 | 3.2.2 | Standard | galvanized pipe 1" |
REV1: Approved |
|
|
| 3.2.3 | rod horizont 1x1x 600 | 3.2.3 | Production | wood strip |
REV1: Approved |
|
||
| 3.2.4 | 1 | nipple 1" | 3.2.4 | Standard | galvanized pipe 1" fitting |
REV1: Approved |
|
|
| 3.2.5 | 2 | Sheet metal bracket | 3.2.5 | Production | steel C45 |
REV1: Approved |
|
|
| 3.3 | bell crank | 3.3 | Production | steel C45 |
REV1: Approved |
|
||
| 3.4 | pivot plate | 3.4 | Production | sheet steel C45 |
REV1: Approved |
|
||
| 3.5 | adjustable pumprod forkend | 3.5 |
REV1: Approved |
|
||||
| 3.5.1 | 2 | Sheet metal bracket | 3.5.1 | Production | sheet steel C45 |
REV1: Approved |
|
|
| 3.5.2 | 1 | nipple 1" | 3.5.2 | Standard | galvanized pipe 1" fitting |
REV1: Approved |
|
|
| 3.5.3 | 1 | water pipe 1"x150 | 3.5.3 | Standard | galvanized pipe 1" |
REV1: Approved |
|
|
| 3.5.4 | 1 | rod vert 1x1x 600 | 3.5.4 | Production | wood strip |
REV1: Approved |
|
|
| 3.5.5 | 1 | stirrup | 3.5.5 | Production | structural steel A36 |
REV1: Approved |
|
|
| 3.5.6 | 2 | sheet metal bracket | 3.5.6 | Production |
REV1: Approved |
|
||
| 3.6 | 16 | bolts M6x30 | 3.6 | Standard | round head screw, galvanized steel |
REV1: Approved |
|
|
| 3.7 | 16 | nut M6 | 3.7 | Standard | galvanized steel |
REV1: Approved |
|
|
| 4 | 1 | pump | 4 |
REV1: Approved |
|
|||
| 4.1 | 1 | pumpbody oring | 4.1 | Production | steel C45 |
REV1: Approved |
|
|
| 4.2 | 1 | pumpbody disk | 4.2 | Production | steel C45 |
REV1: Approved |
|
|
| 4.3 | 1 | rubber diafphragm | 4.3 | Production | rubber |
REV1: Approved |
|
|
| 4.4 | 2 | flange ring | 4.4 | Production | steel C45 |
REV1: Approved |
|
|
| 4.5 | 2 | spacer | 4.5 | Production | wood |
REV1: Approved |
|
|
| 4.6 | 4 | galvanised pipe 1" x 50 | 4.6 | Standard | galvanized pipe 1" |
REV1: Approved |
|
|
| 4.7 | 2 | galvanised elbow 1"-90º | 4.7 | Standard | galvanized pipe 1" fitting |
REV1: Approved |
|
|
| 4.8 | 1 | inlet valve | 4.8 | Standard | galvanized check valve 1" fitting |
REV1: Approved |
|
|
| 4.9 | 1 | outlet valve | 4.9 | Standard | galvanized check valve 1" fitting |
REV1: Approved |
|
|
| 4.10 | 1 | Mounting bar - U1"x2"x6x 350 | 4.10 | Standard | structural steel profile |
REV1: Approved |
|
|
| 4.11 | 8 | bolts M6x30 | 4.11 | Standard | hexagonal head screw, galvanized steel |
REV1: Approved |
|
|
| 4.12 | 8 | nut M6 | 4.12 | Standard | galvanized steel |
REV1: Approved |
|
|