Vertical Axis Sail Windmill - Diameter 3 m
Vertical Axis Sail Windmill - Diameter 3 m Basic Data Category: Savonius wind turbines Keywords: vertical, axis, sail, windmill, diy, oho License: CC BY-SA 4.0 Organization: Low Energy Systems Project status: Active Certification status: In process Technical documentation
Contains PDF-drawings: Yes CAD files are editable: Yes Assembly instructions are published: No Bill of materials is published: Yes
yes yes
|
|
Technical documentation
Complete PDF plans | |
Files: |
CAD files | |
Files: |
Attestation | |
The project Vertical Axis Sail Windmill - Diameter 3 m was reviewed by two reviewers from the OHO team. The review consisted of the following components:
1. Completeness check: Checks if all required documents have been submitted. 2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. 2.1 Bill of materials - Are all parts and assemblies covered? - Are all quantities correct? - Are all required material specifications available? - Are all specifications for purchased parts and standard parts complete? 3.2 Technical drawings - Are all the required views available? - Are all required dimensional data available? 4.1 Suggestions for improvement Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers Permanent Link: https://en.oho.wiki/index.php?title=Vertical_Axis_Sail_Windmill_-_Diameter_3_m&oldid=44316 | |
Files: |
+ General Reviews
Parts list
Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
---|---|---|---|---|---|---|---|---|
A1 | 1 | 3d views |
REV1: Approved |
|||||
A2 | Exploded 3d view |
REV1: Approved |
||||||
B1 | Parts list |
REV1: Approved |
||||||
C1 | Technical notes |
REV1: Approved |
||||||
1.0 | 1 | Tower |
REV1: Approved |
|||||
1.1 | 1 | Timber 5.5m | Production | Wood |
REV1: Approved |
|||
1.2 | 1 | Timber 3.7m | Production | Wood |
REV1: Approved |
|||
1.3 | 4 | Brackets | Production | Steel C45 |
REV1: Approved |
|||
1.4 | Tower bolt | Standard | Tower bolt |
REV1: Approved |
||||
1.5 | 20 | Tower nut | Standard | Tower nut, M10 |
REV1: Approved |
|||
1.6 | 20 | Towr Washer | Standard | Towr Washer, M20 |
REV1: Approved |
|||
1.7 | 16 | Tower bolt piercing | Standard | Tower bolt piercing, M10 x 100 |
REV1: Approved |
|||
1.8 | 2 | Towe eye bolt | Standard | Towe eye bolt, M8 x 12 x 150 |
REV1: Approved |
|||
2.0 | 6 | Tenioner |
REV1: Approved |
|||||
2.1 | 8 | Guy wire | Production | wire of D: 6mm - total:42,0 m, Galvanized steel |
REV1: Approved |
|||
2.2 | 16 | Bulldog grips | Standard | Bulldog grips, Grip 4 mm to 12mm cap., include nut and washers |
REV1: Approved |
|||
2.3 | 8 | Turnbuckles | Standard | Turnbuckles, tensioner for guy of 6 mm |
REV1: Approved |
|||
2.4 | 8 | Angle25 | Production | ASTm A36 |
REV1: Approved |
|||
3.0 | 2 | Foundation | Production | Sheet of 10mm, Steel C45 |
REV1: Approved |
|||
4.0 | 4 | Sail frame | Production | 3m lengths of galvanised conduit D:20mm - Std, Steel Galvanized |
REV1: Approved |
|||
5.0 | 8 | Rotor arm |
REV1: Approved |
|||||
5.1 | 8 | Arms | Production | Galvanized Steel |
REV1: Approved |
|||
5.2 | 8 | Keeklamps | Standard | Keeklamps, 1/2" - will fit 20mm conduit, Plastic |
REV1: Approved |
|||
5.3 | 16 | Rotor bolt | Standard | Rotor bolt |
REV1: Approved |
|||
6.0 | 1 | Axle |
REV1: Approved |
|||||
6.1 | 1 | Axle | Production | Steel C45 |
REV1: Approved |
|||
6.2 | 2 | Steel plate | Production | Steel C45 |
REV1: Approved |
|||
6.3 | 2 | Bearing | Standard | Bearing , D: 25,0 - UCP type - bridge type bearings with set screw |
REV1: Approved |
|||
6.4 | 16 | Axle bolt 1 | Standard | Axle bolt 1, M6 x 40 DIN 933 |
REV1: Approved |
|||
6.5 | 16 | Axle nut 1 | Standard | Axle nut 1, M6 DIN 934 |
REV1: Approved |
|||
6.6 | 16 | Axle Washer 1 | Standard | Axle Washer 1, D: 6,0 |
REV1: Approved |
|||
6.7 | 8 | Axle bolt 2 | Standard | Axle bolt 2, M10 x 130 DIN 933 |
REV1: Approved |
|||
6.8 | 4 | Axle nut 2 | Standard | Axle nut 2, M6 DIN 934 |
REV1: Approved |
|||
6.9 | 4 | Axle washer 2 | Standard | Axle washer 2, D: 10 |
REV1: Approved |
|||
7.0 | 4 | Sail |
REV1: Approved |
|||||
7.1 | 4 | Sail | Production | e=2,0mm, canva of linen or synthetic |
REV1: Approved |
|||
7.2 | 8 | Cord | Standard | Cord, 550 mm longt, cord 6mm 3 twisted, Prolypropylene |
REV1: Approved |
|||
7.3 | 8 | Eyelet | Standard | Eyelet, snap eyelet for canva D:8mm, Bronce |
REV1: Approved |
|||