Difference between revisions of "Talk:Whater Wheel Diameter 2m"

From OHO - search engine for sustainable open hardware projects
 
(16 intermediate revisions by 3 users not shown)
Line 38: Line 38:


Steel C45 material.
Steel C45 material.
== Part number 2.8 -- [[User:Jeefri|Jeefri]] ([[User talk:Jeefri|talk]]) 17:17, 4 January 2022 (CET) ==
Indicate cutting angle.
== Part number 3.1 -- [[User:Jeefri|Jeefri]] ([[User talk:Jeefri|talk]]) 17:17, 4 January 2022 (CET) ==
Steel C45 Hardened Material.
== Part number 3.0 -- [[User:Jeefri|Jeefri]] ([[User talk:Jeefri|talk]]) 17:17, 4 January 2022 (CET) ==
Indicate method of connection between wood base and concrete pedestal. It is suggested to change the 3.2 piece for a steel plate that will be welded to an anchor plate embedded in the concrete.
== Part number C1 -- [[User:Jeefri|Jeefri]] ([[User talk:Jeefri|talk]]) 17:18, 4 January 2022 (CET) ==
If available, indicate equipment capacity, limiting fluid volume, limiting wheel rotation speeds.
==  -- [[User:Jaimerosciano|Jaimerosciano]] ([[User talk:Jaimerosciano|talk]]) 23:34, 5 January 2022 (CET) ==
It should be mentioned that the efficiency of the water wheel is based on the increase of the wheel speed, that is to say, more turns per minute, this can be achieved in two ways, with a higher water flow that fills the buckets very fast and thus allows the rotation, or with a gearbox.
==  -- [[User:Dmosquera1968|Dmosquera1968]] ([[User talk:Dmosquera1968|talk]]) 00:00, 12 January 2022 (CET) ==
It would be interesting to be able to adjust the relative position between the water discharge and the wheel axle, to optimize the energy conversion, as the flow rate will affect the horizontal range of the jet.
== Part number 1.0 -- [[User:Dmosquera1968|Dmosquera1968]] ([[User talk:Dmosquera1968|talk]]) 00:00, 12 January 2022 (CET) ==
In thin sheet joints, it is recommended to use rivets instead of welding.
== Part number 2.5 -- [[User:Dmosquera1968|Dmosquera1968]] ([[User talk:Dmosquera1968|talk]]) 00:00, 12 January 2022 (CET) ==
A half lap joint is recommended, so as not to weaken this piece so much.
== Part number 3.0 -- [[User:Dmosquera1968|Dmosquera1968]] ([[User talk:Dmosquera1968|talk]]) 00:00, 12 January 2022 (CET) ==
Use circlips, cotter pins or diameter reductions to prevent axial slippage
== Part number 3.3 -- [[User:Dmosquera1968|Dmosquera1968]] ([[User talk:Dmosquera1968|talk]]) 00:00, 12 January 2022 (CET) ==
Visual representation of the required steel grating

Latest revision as of 05:10, 13 January 2022

Part number B1 -- Dmosquera1968 (talk) 13:52, 22 December 2021 (CET)

It could inform the variations of the structure according to the terrain where it will be installed.

Part number 2.0 -- Dmosquera1968 (talk) 13:54, 22 December 2021 (CET)

It could inform the variations of the longt e according to the terrain where it will be installed.

Part number 1.1 -- Jeefri (talk) 17:13, 4 January 2022 (CET)

Indicate sheet size.

Part number 1.2 -- Jeefri (talk) 17:14, 4 January 2022 (CET)

  • The dimensions of the holes must be aligned with the parallel external face and indicate the distance to the edge.
  • Indicate sheet size.

Part number 1.3 -- Jeefri (talk) 17:14, 4 January 2022 (CET)

  • Indicate sheet size.
  • Detail of the chamfer on the corners.

Part number 1.4 -- Jeefri (talk) 17:15, 4 January 2022 (CET)

  • Indicate sheet size.
  • Indicate distance to the edge of the holes.

Part number 1.5 -- Jeefri (talk) 17:16, 4 January 2022 (CET)

Indicate sheet size.

Part number 1.6 -- Jeefri (talk) 17:16, 4 January 2022 (CET)

Indicate sheet size.

Part number 1.7 -- Jeefri (talk) 17:16, 4 January 2022 (CET)

Steel C45 material.

Part number 2.8 -- Jeefri (talk) 17:17, 4 January 2022 (CET)

Indicate cutting angle.

Part number 3.1 -- Jeefri (talk) 17:17, 4 January 2022 (CET)

Steel C45 Hardened Material.

Part number 3.0 -- Jeefri (talk) 17:17, 4 January 2022 (CET)

Indicate method of connection between wood base and concrete pedestal. It is suggested to change the 3.2 piece for a steel plate that will be welded to an anchor plate embedded in the concrete.

Part number C1 -- Jeefri (talk) 17:18, 4 January 2022 (CET)

If available, indicate equipment capacity, limiting fluid volume, limiting wheel rotation speeds.

-- Jaimerosciano (talk) 23:34, 5 January 2022 (CET)

It should be mentioned that the efficiency of the water wheel is based on the increase of the wheel speed, that is to say, more turns per minute, this can be achieved in two ways, with a higher water flow that fills the buckets very fast and thus allows the rotation, or with a gearbox.

-- Dmosquera1968 (talk) 00:00, 12 January 2022 (CET)

It would be interesting to be able to adjust the relative position between the water discharge and the wheel axle, to optimize the energy conversion, as the flow rate will affect the horizontal range of the jet.

Part number 1.0 -- Dmosquera1968 (talk) 00:00, 12 January 2022 (CET)

In thin sheet joints, it is recommended to use rivets instead of welding.

Part number 2.5 -- Dmosquera1968 (talk) 00:00, 12 January 2022 (CET)

A half lap joint is recommended, so as not to weaken this piece so much.

Part number 3.0 -- Dmosquera1968 (talk) 00:00, 12 January 2022 (CET)

Use circlips, cotter pins or diameter reductions to prevent axial slippage

Part number 3.3 -- Dmosquera1968 (talk) 00:00, 12 January 2022 (CET)

Visual representation of the required steel grating

OPEN HARDWARE OBSERVATORY 2020
| |
|||