Talk:Small water turbine

From OHO - search engine for sustainable open hardware projects

Part number 1 -- Xtech2020 review (talk) 02:58, 3 March 2021 (CET)

this pdf drawing is missing

Re: Part number 1 -- Inddigital (talk) 01:32, 7 March 2021 (CET)

Solved!

Part number B -- Xtech2020 review (talk) 03:06, 3 March 2021 (CET)

  • In parts list online it says "CAST IRON", in pdf it says nothing
  • Cast iron can not be used, because in small scale this technology is not used.

Part number 3.3 -- Xtech2020 review (talk) 03:10, 3 March 2021 (CET)

What is the thickness of this part?

Re: Part number 3.3 -- Inddigital (talk) 01:02, 4 March 2021 (CET)

Hi xtech, your comment has been resolved, please remove the Action Required check mark.

Part number B -- Xtech2020 review (talk) 03:16, 3 March 2021 (CET)

it is recommended to indicate DIN references for fasteners parts

-- Xtech2020 review (talk) 03:20, 3 March 2021 (CET)

It is suggested to include some theoretical estimates of equipment capacity and efficiency.

Re: -- Inddigital (talk) 00:34, 4 March 2021 (CET)

you can get a complete theoretical analysis at: https://dspace.mit.edu/handle/1721.1/27493

Among others, some characteristic curves of the equipment are shown, like this one:

Oseg swt curves1.jpg

Part number B -- Xtech2020 review (talk) 19:48, 3 March 2021 (CET)

In some items it says cap machine, I think it is a mistake.

Part number B -- Xtech2020 review (talk) 19:50, 3 March 2021 (CET)

the Sheet and Qty columns must be updated

Part number 11.3 -- Xtech2020 review (talk) 19:57, 3 March 2021 (CET)

Specifications of this Standard part are missing

Re: Part number 11.3 -- Inddigital (talk) 03:34, 4 March 2021 (CET)

Answered

Part number 11.5 -- Xtech2020 review (talk) 19:58, 3 March 2021 (CET)

Specifications of this Standard part are missing

Re: Part number 11.5 -- Inddigital (talk) 03:34, 4 March 2021 (CET)

Answered

Part number 5 -- Xtech2020 review (talk) 23:19, 3 March 2021 (CET)

For sliding fit moving parts, it is highly recommended to place dimensional tolerances on the dimensions where applicable. In the absence of this, a general value could be specified for these dimensions

Re: Part number 5 -- Inddigital (talk) 01:09, 4 March 2021 (CET)

Thanks for your suggestion, a new thread has been opened in general comments, to highlight this point.

-- Xtech2020 review (talk) 23:44, 3 March 2021 (CET)

Most of the parts are missing material specification

Re: -- Inddigital (talk) 01:31, 7 March 2021 (CET)

Thank you for your comment, this issue has been resolved.

Part number 7.2 -- Xtech2020 review (talk) 23:55, 3 March 2021 (CET)

this piece does not appear to correspond to any of the original design, it should be removed.

Re: Part number 7.2 -- Inddigital (talk) 03:26, 4 March 2021 (CET)

I'm going to check it out

-- Inddigital (talk) 01:06, 4 March 2021 (CET)

In cases of sliding parts, use 0.2 mm as tolerance for diametrical dimensions. This item has been included in technical notes.

Part number 6.2 -- Xtech2020 review (talk) 01:12, 4 March 2021 (CET)

this pdf drawing is missing

Part number B -- Inddigital (talk) 02:40, 4 March 2021 (CET)

Some of the required updates was solved, I will post the rest as soon as possible. Regarding the DIN code for the screws, I will try to keep it as it is, since they are size references under American standard with DIN and ISO equivalents easily found.

Part number 2 -- Xtech2020 review (talk) 02:51, 4 March 2021 (CET)

this pdf drawing is missing

Re: Part number 2 -- Inddigital (talk) 01:33, 7 March 2021 (CET)

Solved!

Part number 3.1 -- Xtech2020 review (talk) 18:30, 6 March 2021 (CET)

Missing material

Part number 4 -- Xtech2020 review (talk) 18:32, 6 March 2021 (CET)

  • What material?
  • How it is manufactured?

Part number 5 -- Xtech2020 review (talk) 18:34, 6 March 2021 (CET)

  • The blades views are missing
  • How is it manufactured?

Part number 7.1 -- Xtech2020 review (talk) 18:35, 6 March 2021 (CET)

How is it manufactured?

OPEN HARDWARE OBSERVATORY 2020
| |
|||