Difference between revisions of "Talk:Cross Flow Turbine"
(→Part number 7.11.0 -- ~~~~: new section) |
(→Part number 7.6.0 -- ~~~~: new section) |
||
Line 64: | Line 64: | ||
It is recommended to purchase this part. | It is recommended to purchase this part. | ||
== Part number 7.6.0 -- [[User:Jaimerosciano|Jaimerosciano]] ([[User talk:Jaimerosciano|talk]]) 21:19, 14 December 2021 (CET) == | |||
Recommend a flywheel instead of this lever, to provide a torque to compensate the effort generated by the fluid pressure. |
Revision as of 22:19, 14 December 2021
Part number C1 -- Jeefri (talk) 03:04, 13 December 2021 (CET)
• Eliminate (Wood treatment), the project does not contemplate wooden parts.
• Remove sheet C2 from the PDF file.
Part number 2.1.0 -- Jeefri (talk) 03:04, 13 December 2021 (CET)
• Add distance dimension from the top holes of 8mm to the top edge of the plate.
• Add distance from the bottom holes of 8mm to the inside edge of the plate.
Part number 2.5.0 -- Jeefri (talk) 03:05, 13 December 2021 (CET)
• Consider separating the pieces as they are distinct elements.
Part number 2.6.0 -- Jeefri (talk) 03:06, 13 December 2021 (CET)
• Consider separating the pieces as they are distinct elements.
Part number 3.1.2 -- Jeefri (talk) 03:06, 13 December 2021 (CET)
• Indicate the thickness of the part.
Part number 3.2.0 -- Jeefri (talk) 03:06, 13 December 2021 (CET)
• Indicate the thickness of the part.
Part number 3.3.0 -- Jeefri (talk) 03:06, 13 December 2021 (CET)
• Indicate the thickness of the part.
Part number 5.4.0 -- Jeefri (talk) 03:07, 13 December 2021 (CET)
• Consider separating the pieces as they are distinct elements.
Part number 6.4.0 -- Jeefri (talk) 03:07, 13 December 2021 (CET)
• Add smaller internal diameter.
Part number 7.1.0 -- Jeefri (talk) 03:07, 13 December 2021 (CET)
• Indicate the thickness of the part.
Part number 7.10.0 -- Jeefri (talk) 03:08, 13 December 2021 (CET)
• Consider separating the pieces as they are distinct elements.
Part number 7.11.0 -- Jeefri (talk) 03:08, 13 December 2021 (CET)
• Consider separating the pieces as they are distinct elements.
-- Jaimerosciano (talk) 18:10, 14 December 2021 (CET)
-Indicates the flow rate to be handled - In each bolted joint where water circulates, recommend the use of gaskets. - The elements in contact with water should be painted with special paint to prevent corrosion.
Part number 2.8.0 -- Jaimerosciano (talk) 21:16, 14 December 2021 (CET)
Implement a greater thickness of sheet, or more of this part to allow a better support and avoid vibrations.
Part number 7.11.0 -- Jaimerosciano (talk) 21:18, 14 December 2021 (CET)
It is recommended to purchase this part.
Part number 7.6.0 -- Jaimerosciano (talk) 21:19, 14 December 2021 (CET)
Recommend a flywheel instead of this lever, to provide a torque to compensate the effort generated by the fluid pressure.