Difference between revisions of "Small water turbine"
Inddigital (talk | contribs) |
Inddigital (talk | contribs) |
||
(13 intermediate revisions by 3 users not shown) | |||
Line 39: | Line 39: | ||
|trans_status=WT | |trans_status=WT | ||
|desc=<p>This project shows the construction plans for a small 5 kW water turbine based on the research of Dr. Mohammad Durali at MIT.</p> | |desc=<p>This project shows the construction plans for a small 5 kW water turbine based on the research of Dr. Mohammad Durali at MIT.</p> | ||
<p>Project published under a CERN-OHL license</p> | <p>According to the original development, the equipment would be used to feed an electrical network (coffee farm in South America), which is why they have selected a 60Hz generator, however, I believe that this can be adapted to the needs of whoever is going to replicate it. In any case, the same original design was followed.</p> | ||
<p>Project published under a CERN-OHL license.</p> | |||
|licence=COHL12 | |licence=COHL12 | ||
|typeproject=Web | |typeproject=Web | ||
Line 63: | Line 64: | ||
|cmptitle=CAD Files | |cmptitle=CAD Files | ||
|cmpimage=Oseg swt render1.jpg | |cmpimage=Oseg swt render1.jpg | ||
|cmpfile1=Oseg swt CAD-files | |cmpfile1=Oseg swt CAD-files.zip | ||
|cmpfile2=Oseg swt | |cmpfile2=Oseg swt STP-files.zip | ||
}} | }} | ||
|Materials={{ProjektMaterials | |Materials={{ProjektMaterials | ||
Line 73: | Line 72: | ||
|matdrawingsheet=A1 | |matdrawingsheet=A1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt A1 | |matpdffile=Oseg swt A1 Small water turbine.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=A2 | |matpartnumber=A2 | ||
Line 79: | Line 80: | ||
|matdrawingsheet=A2 | |matdrawingsheet=A2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt A2 small-water- | |matpdffile=Oseg swt A2 small-water-turbiner.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=B | |matpartnumber=B | ||
|matdesc=Parts-list | |matdesc=Parts-list | ||
|matdrawingsheet=B | |matdrawingsheet=B | ||
|matpdffile=Oseg swt B | |matpdffile=Oseg swt B part-list.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
|status_rev_2=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=C | |||
|matdesc=Technical notes | |||
|matdrawingsheet=C | |||
|matspec=General notes | |||
|matpdffile=Oseg swt C technical-notes.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=1 | |matpartnumber=1 | ||
Line 94: | Line 106: | ||
|matparttype=production | |matparttype=production | ||
|matspec=CAST IRON | |matspec=CAST IRON | ||
|status_rev_1= | |matpdffile=Oseg swt 1.0 front adaptor.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=2 | |matpartnumber=2 | ||
|matposold=AF312 | |matposold=AF312 | ||
|matquantity=1 | |matquantity=1 | ||
|matdesc= | |matdesc=middle section | ||
|matdrawingsheet=2 | |matdrawingsheet=2 | ||
|matparttype=production | |matparttype=production | ||
|matspec=CAST IRON | |matspec=CAST IRON | ||
|status_rev_1= | |matpdffile=Oseg swt 2.0 middle section.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3 | |matpartnumber=3 | ||
Line 112: | Line 128: | ||
|matparttype=production | |matparttype=production | ||
|matspec=STEEL C45 | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.0 drain | |matpdffile=Oseg swt 3.0 drain chute.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.1 | |matpartnumber=3.1 | ||
Line 119: | Line 137: | ||
|matdrawingsheet=3.1 | |matdrawingsheet=3.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.1 back | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.1 back plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.2 | |matpartnumber=3.2 | ||
Line 126: | Line 147: | ||
|matdrawingsheet=3.2 | |matdrawingsheet=3.2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.2 front | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.2 front flange.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.3 | |matpartnumber=3.3 | ||
Line 133: | Line 157: | ||
|matdrawingsheet=3.3 | |matdrawingsheet=3.3 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.3 | |matspec=STEEL C45 | ||
|status_rev_1= | |matpdffile=Oseg swt 3.3 curved plate.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.4 | |matpartnumber=3.4 | ||
Line 142: | Line 168: | ||
|matdrawingsheet=3.4 | |matdrawingsheet=3.4 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.4 side | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.4 side plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.5 | |matpartnumber=3.5 | ||
Line 149: | Line 178: | ||
|matdrawingsheet=3.5 | |matdrawingsheet=3.5 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.5 front | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.5 front plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4 | |matpartnumber=4 | ||
Line 156: | Line 188: | ||
|matdrawingsheet=4 | |matdrawingsheet=4 | ||
|matparttype=production | |matparttype=production | ||
|matspec= | |matspec=See Technical notes | ||
|matpdffile=Oseg swt 4.0 | |matpdffile=Oseg swt 4.0 NOSE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=5 | |matpartnumber=5 | ||
Line 164: | Line 198: | ||
|matdrawingsheet=5 | |matdrawingsheet=5 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 5.0 | |matspec=See Technical notes | ||
|status_rev_1= | |matpdffile=Oseg swt 5.0 STATOR BLADING.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=6 | |matpartnumber=6 | ||
Line 172: | Line 208: | ||
|matdrawingsheet=6 | |matdrawingsheet=6 | ||
|matparttype=production | |matparttype=production | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=6.1 | |matpartnumber=6.1 | ||
Line 177: | Line 215: | ||
|matdrawingsheet=6.1 | |matdrawingsheet=6.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 6.1 | |matspec=See Technical notes | ||
|matpdffile=Oseg swt 6.1 ROTOR BLADING.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=6.2 | |matpartnumber=6.2 | ||
Line 183: | Line 224: | ||
|matdrawingsheet=6.2 | |matdrawingsheet=6.2 | ||
|matparttype=production | |matparttype=production | ||
|status_rev_1= | |matspec=1,5 mm STEEL SHEET | ||
|matpdffile=Oseg swt 6.2 ROTOR WASHER.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=7 | |matpartnumber=7 | ||
Line 190: | Line 234: | ||
|matdrawingsheet=7 | |matdrawingsheet=7 | ||
|matparttype=production | |matparttype=production | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=7.1 | |matpartnumber=7.1 | ||
Line 195: | Line 241: | ||
|matdrawingsheet=7.1 | |matdrawingsheet=7.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 7.1 diffuser | |matspec=See Technical notes | ||
|matpdffile=Oseg swt 7.1 diffuser blanding.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=7.2 | |matpartnumber=7.2 | ||
Line 201: | Line 250: | ||
|matdrawingsheet=7.2 | |matdrawingsheet=7.2 | ||
|matparttype=production | |matparttype=production | ||
|status_rev_1= | |matspec=1,5 mm STEEL SHEET | ||
|matpdffile=Oseg swt 7.2 DIFFUSER WASHER.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=8 | |matpartnumber=8 | ||
Line 208: | Line 260: | ||
|matdrawingsheet=8 | |matdrawingsheet=8 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 8.0 bush | |matspec=see tech. notes | ||
|matpdffile=Oseg swt 8.0 bush.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=9 | |matpartnumber=9 | ||
Line 216: | Line 271: | ||
|matparttype=production | |matparttype=production | ||
|matspec=ALUMINIUM | |matspec=ALUMINIUM | ||
|matpdffile=Oseg swt 9.0 | |matpdffile=Oseg swt 9.0 slotter disk.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=10 | |matpartnumber=10 | ||
Line 223: | Line 280: | ||
|matdrawingsheet=10 | |matdrawingsheet=10 | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=key 6 x 6 x 36.0 | |matspec=key 6 x 6 x 36.0, HARD STEEL | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11 | |matpartnumber=11 | ||
Line 229: | Line 288: | ||
|matdrawingsheet=11 | |matdrawingsheet=11 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 11.0 hub | |matpdffile=Oseg swt 11.0 hub assembly.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.1 | |matpartnumber=11.1 | ||
Line 236: | Line 297: | ||
|matdrawingsheet=11.1 | |matdrawingsheet=11.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 11.1 shaft | |matspec=STAINLESS STEEL | ||
|matpdffile=Oseg swt 11.1 shaft.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.2 | |matpartnumber=11.2 | ||
Line 244: | Line 308: | ||
|matparttype=production | |matparttype=production | ||
|matspec=CAST STEEL | |matspec=CAST STEEL | ||
|matpdffile=Oseg swt 11.2 hub-housing | |matpdffile=Oseg swt 11.2 hub-housing.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.3 | |matpartnumber=11.3 | ||
Line 252: | Line 318: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=1,5 mm STEEL SHEET | |matspec=1,5 mm STEEL SHEET | ||
|status_rev_1= | |status_rev_1=approved | ||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.4 | |matpartnumber=11.4 | ||
Line 260: | Line 327: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=bearing 206-SX adater and nut G-Y or equivalent estándar part | |matspec=bearing 206-SX adater and nut G-Y or equivalent estándar part | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.5 | |matpartnumber=11.5 | ||
Line 267: | Line 336: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=GARLOCK 78*0542 | |matspec=GARLOCK 78*0542 | ||
|status_rev_1= | |status_rev_1=approved | ||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.6 | |matpartnumber=11.6 | ||
Line 275: | Line 345: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=brownign 40P60 - 1/2" pich - 60 teeth - Dia.: 9.55" | |matspec=brownign 40P60 - 1/2" pich - 60 teeth - Dia.: 9.55" | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.7 | |matpartnumber=11.7 | ||
Line 282: | Line 354: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=brownign Nº 4024 - 1/2" pich - 24 teeth - Dia.: 3.83" | |matspec=brownign Nº 4024 - 1/2" pich - 24 teeth - Dia.: 3.83" | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.8 | |matpartnumber=11.8 | ||
Line 289: | Line 363: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=brownign Nº 40 - 1/2" pich Nº 40 | |matspec=brownign Nº 40 - 1/2" pich Nº 40 | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.9 | |matpartnumber=11.9 | ||
Line 295: | Line 371: | ||
|matdrawingsheet=11.9 | |matdrawingsheet=11.9 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12 | |matpartnumber=12 | ||
Line 301: | Line 379: | ||
|matdrawingsheet=12 | |matdrawingsheet=12 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.0 frame | |matpdffile=Oseg swt 12.0 frame.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12.1 | |matpartnumber=12.1 | ||
Line 308: | Line 388: | ||
|matdrawingsheet=12.1 | |matdrawingsheet=12.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.1 side | |matspec=steel A36 | ||
|matpdffile=Oseg swt 12.1 side angle.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12.2 | |matpartnumber=12.2 | ||
Line 315: | Line 398: | ||
|matdrawingsheet=12.2 | |matdrawingsheet=12.2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.2 top | |matspec=steel A36 | ||
|matpdffile=Oseg swt 12.2 top angle.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12.3 | |matpartnumber=12.3 | ||
Line 322: | Line 408: | ||
|matdrawingsheet=12.3 | |matdrawingsheet=12.3 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.3 top | |matspec=steel A36 | ||
|matpdffile=Oseg swt 12.3 top plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12.4 | |matpartnumber=12.4 | ||
|matposold=AF3227D | |matposold=AF3227D | ||
|matdesc=bar | |matdesc=bar plate | ||
|matdrawingsheet=12.4 | |matdrawingsheet=12.4 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.4 bar | |matspec=steel A36 | ||
|matpdffile=Oseg swt 12.4 bar plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12.5 | |matpartnumber=12.5 | ||
Line 336: | Line 428: | ||
|matdrawingsheet=12.5 | |matdrawingsheet=12.5 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.5 fundation | |matspec=steel A36 | ||
|matpdffile=Oseg swt 12.5 fundation plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13 | |matpartnumber=13 | ||
Line 343: | Line 438: | ||
|matdrawingsheet=13 | |matdrawingsheet=13 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 13.0 oil | |matpdffile=Oseg swt 13.0 oil bath.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13.1 | |matpartnumber=13.1 | ||
Line 349: | Line 446: | ||
|matdrawingsheet=13.1 | |matdrawingsheet=13.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 13.1 plate | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 13.1 plate front cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13.2 | |matpartnumber=13.2 | ||
Line 355: | Line 455: | ||
|matdrawingsheet=13.2 | |matdrawingsheet=13.2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 13.2 band | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 13.2 band side cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13.3 | |matpartnumber=13.3 | ||
Line 361: | Line 464: | ||
|matdrawingsheet=13.3 | |matdrawingsheet=13.3 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile= | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 13.3 plate down cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13.4 | |matpartnumber=13.4 | ||
Line 367: | Line 473: | ||
|matdrawingsheet=13.4 | |matdrawingsheet=13.4 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 13.4 brake | |matspec=STEEL A36 | ||
|matpdffile=Oseg swt 13.4 brake angle cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13.5 | |matpartnumber=13.5 | ||
Line 373: | Line 482: | ||
|matdrawingsheet=13.5 | |matdrawingsheet=13.5 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 13.5 brake | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 13.5 brake bar cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=14 | |matpartnumber=14 | ||
Line 380: | Line 492: | ||
|matdrawingsheet=14 | |matdrawingsheet=14 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 14.0 back | |matpdffile=Oseg swt 14.0 back oil bath.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=14.1 | |matpartnumber=14.1 | ||
Line 386: | Line 500: | ||
|matdrawingsheet=14.1 | |matdrawingsheet=14.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 14.1 plate | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 14.1 plate back cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=14.2 | |matpartnumber=14.2 | ||
Line 392: | Line 509: | ||
|matdrawingsheet=14.2 | |matdrawingsheet=14.2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 14.2 | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 14.2 bar for plate front.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=15 | |matpartnumber=15 | ||
Line 400: | Line 520: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=5 KW; 115-230 V;21,5 A; 60Hz | |matspec=5 KW; 115-230 V;21,5 A; 60Hz | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=16 | |matpartnumber=16 | ||
Line 407: | Line 529: | ||
|matdrawingsheet=16 | |matdrawingsheet=16 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=17 | |matpartnumber=17 | ||
Line 414: | Line 538: | ||
|matdrawingsheet=17 | |matdrawingsheet=17 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=18 | |matpartnumber=18 | ||
Line 421: | Line 547: | ||
|matdrawingsheet=18 | |matdrawingsheet=18 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=19 | |matpartnumber=19 | ||
Line 428: | Line 556: | ||
|matdrawingsheet=19 | |matdrawingsheet=19 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=20 | |matpartnumber=20 | ||
Line 435: | Line 565: | ||
|matdrawingsheet=20 | |matdrawingsheet=20 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=21 | |matpartnumber=21 | ||
Line 442: | Line 574: | ||
|matdrawingsheet=21 | |matdrawingsheet=21 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=22 | |matpartnumber=22 | ||
Line 449: | Line 583: | ||
|matdrawingsheet=22 | |matdrawingsheet=22 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=23 | |matpartnumber=23 | ||
Line 456: | Line 592: | ||
|matdrawingsheet=23 | |matdrawingsheet=23 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=24 | |matpartnumber=24 | ||
Line 463: | Line 601: | ||
|matdrawingsheet=24 | |matdrawingsheet=24 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=25 | |matpartnumber=25 | ||
Line 470: | Line 610: | ||
|matdrawingsheet=25 | |matdrawingsheet=25 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=26 | |matpartnumber=26 | ||
Line 477: | Line 619: | ||
|matdrawingsheet=26 | |matdrawingsheet=26 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=27 | |matpartnumber=27 | ||
Line 484: | Line 628: | ||
|matdrawingsheet=27 | |matdrawingsheet=27 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=28 | |matpartnumber=28 | ||
Line 491: | Line 637: | ||
|matdrawingsheet=28 | |matdrawingsheet=28 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=29 | |matpartnumber=29 | ||
Line 499: | Line 647: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=HARD STEEL | |matspec=HARD STEEL | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}} | }} | ||
|certificate_requested=No | |certificate_requested=No | ||
|certificate_status=in process | |certificate_status=in process | ||
|reviewer1=Xtech2020 review | |reviewer1=Xtech2020 review | ||
|reviewer2=Thehunter | |||
}} | }} |
Revision as of 00:01, 7 April 2021
Small water turbine Basic Data Category: Small Water turbines URL (first publication): https://dspace.mit.edu/handle/1721.1/27493 Keywords: turbine, hidraulic, turbomachinery, water, renewable, sustainable, electric power, mit License: CERN OHL v1.2 Organization: Practical Action Project status: Active Certification status: In process Technical documentation Maturity of the project: prototype
Contains PDF-drawings: Yes Assembly instructions are published: No Bill of materials is published: Yes
yes yes
|
|
Description
This project shows the construction plans for a small 5 kW water turbine based on the research of Dr. Mohammad Durali at MIT.
According to the original development, the equipment would be used to feed an electrical network (coffee farm in South America), which is why they have selected a 60Hz generator, however, I believe that this can be adapted to the needs of whoever is going to replicate it. In any case, the same original design was followed.
Project published under a CERN-OHL license.
Technical documentation
PDF Plans | |
Files: |
CAD Files | |
Files: |
+ General Reviews
Parts list
Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
---|---|---|---|---|---|---|---|---|
A1 | small water turbine | A1 | Production |
REV1: Approved |
||||
A2 | Presentation | A2 | Production |
REV1: Approved |
||||
B | Parts-list | B |
REV1: Approved |
|||||
C | Technical notes | C | General notes |
REV1: Approved |
||||
1 | 1 | front adaptor | 1 | Production | CAST IRON |
REV1: Approved |
||
2 | 1 | middle section | 2 | Production | CAST IRON |
REV1: Approved |
||
3 | 1 | drain chute | 3 | Production | STEEL C45 |
REV1: Approved |
||
3.1 | back plate | 3.1 | Production | STEEL C45 |
REV1: Approved |
|||
3.2 | front flange | 3.2 | Production | STEEL C45 |
REV1: Approved |
|||
3.3 | curved plate | 3.3 | Production | STEEL C45 |
REV1: Approved |
|||
3.4 | 2 | side plate | 3.4 | Production | STEEL C45 |
REV1: Approved |
||
3.5 | front plate | 3.5 | Production | STEEL C45 |
REV1: Approved |
|||
4 | nose | 4 | Production | See Technical notes |
REV1: Approved |
|||
5 | stator blading | 5 | Production | See Technical notes |
REV1: Approved |
|||
6 | rotor blading | 6 | Production |
REV1: Approved |
||||
6.1 | rotor blading | 6.1 | Production | See Technical notes |
REV1: Approved |
|||
6.2 | rotor washer | 6.2 | Production | 1,5 mm STEEL SHEET |
REV1: Approved |
|||
7 | diffuser blanding | 7 | Production |
REV1: Approved |
||||
7.1 | diffuser blanding | 7.1 | Production | See Technical notes |
REV1: Approved |
|||
7.2 | diffuser washer | 7.2 | Production | 1,5 mm STEEL SHEET |
REV1: Approved |
|||
8 | bush | 8 | Production | see tech. notes |
REV1: Approved |
|||
9 | slotted disk | 9 | Production | ALUMINIUM |
REV1: Approved |
|||
10 | key | 10 | Standard | key 6 x 6 x 36.0, HARD STEEL |
REV1: Approved |
|||
11 | Transmission (hub assembly) | 11 | Production |
REV1: Approved |
||||
11.1 | shaft | 11.1 | Production | STAINLESS STEEL |
REV1: Approved |
|||
11.2 | hub housing | 11.2 | Production | CAST STEEL |
REV1: Approved |
|||
11.3 | front cap | 11.3 | Standard | 1,5 mm STEEL SHEET |
REV1: Approved |
|||
11.4 | ball bearing | 11.4 | Standard | bearing 206-SX adater and nut G-Y or equivalent estándar part |
REV1: Approved |
|||
11.5 | seal | 11.5 | Standard | GARLOCK 78*0542 |
REV1: Approved |
|||
11.6 | big sprocket | 11.6 | Standard | brownign 40P60 - 1/2" pich - 60 teeth - Dia.: 9.55" |
REV1: Approved |
|||
11.7 | small sprocket | 11.7 | Standard | brownign Nº 4024 - 1/2" pich - 24 teeth - Dia.: 3.83" |
REV1: Approved |
|||
11.8 | chain | 11.8 | Standard | brownign Nº 40 - 1/2" pich Nº 40 |
REV1: Approved |
|||
11.9 | bolt 3/16" x 32 x 5/16" | 11.9 | Standard |
REV1: Approved |
||||
12 | frame | 12 | Production |
REV1: Approved |
||||
12.1 | side angles | 12.1 | Production | steel A36 |
REV1: Approved |
|||
12.2 | top angle | 12.2 | Production | steel A36 |
REV1: Approved |
|||
12.3 | top plate | 12.3 | Production | steel A36 |
REV1: Approved |
|||
12.4 | bar plate | 12.4 | Production | steel A36 |
REV1: Approved |
|||
12.5 | foundation plate | 12.5 | Production | steel A36 |
REV1: Approved |
|||
13 | oil bath cover | 13 | Production |
REV1: Approved |
||||
13.1 | plate front cover | 13.1 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|||
13.2 | band side cover | 13.2 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|||
13.3 | plate down cover | 13.3 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|||
13.4 | brake angle cover | 13.4 | Production | STEEL A36 |
REV1: Approved |
|||
13.5 | brake bar cover | 13.5 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|||
14 | back oil bath cover | 14 | Production |
REV1: Approved |
||||
14.1 | plate back cover | 14.1 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|||
14.2 | bar for plate front | 14.2 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|||
15 | Generator | 15 | Standard | 5 KW; 115-230 V;21,5 A; 60Hz |
REV1: Approved |
|||
16 | 20 | bolt 5/8"x12 - 2 1/2" | 16 | Standard |
REV1: Approved |
|||
17 | 20 | nut 5/8"x12 | 17 | Standard |
REV1: Approved |
|||
18 | 20 | plain washer 5/8" | 18 | Standard |
REV1: Approved |
|||
19 | 4 | bolt 1/2"x12 - 1 1/2" | 19 | Standard |
REV1: Approved |
|||
20 | 4 | nut 1/2"x12 | 20 | Standard |
REV1: Approved |
|||
21 | 4 | plain washer 1/2" | 21 | Standard |
REV1: Approved |
|||
22 | 4 | bolt 9/16"x12 - 2" | 22 | Standard |
REV1: Approved |
|||
23 | 4 | nut 9/16"x12 | 23 | Standard |
REV1: Approved |
|||
24 | 4 | plain washer 9/16" | 24 | Standard |
REV1: Approved |
|||
25 | 4 | lock washer 9/16" | 25 | Standard |
REV1: Approved |
|||
26 | 1 | bolt 3/8"x16 - 2" | 26 | Standard |
REV1: Approved |
|||
27 | 2 | wing nut 3/8"x16 | 27 | Standard |
REV1: Approved |
|||
28 | 1 | plain washer 3/8" | 28 | Standard |
REV1: Approved |
|||
29 | 4 | ALIGNMENT-PIN | 29 | Standard | HARD STEEL |
REV1: Approved |
||