Difference between revisions of "Small water turbine"
From OHO - search engine for sustainable open hardware projects
Inddigital (talk | contribs) |
|||
| (18 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
{{Projekt | {{Projekt | ||
|Images={{ProjektImages | |Images={{ProjektImages | ||
|projectimage=Oseg swt small-water-turbine 000.jpg | |||
}}{{ProjektImages | |||
|projectimage=Oseg swt A1 small-water-turbine 001.jpg | |projectimage=Oseg swt A1 small-water-turbine 001.jpg | ||
}}{{ProjektImages | }}{{ProjektImages | ||
| Line 37: | Line 39: | ||
|trans_status=WT | |trans_status=WT | ||
|desc=<p>This project shows the construction plans for a small 5 kW water turbine based on the research of Dr. Mohammad Durali at MIT.</p> | |desc=<p>This project shows the construction plans for a small 5 kW water turbine based on the research of Dr. Mohammad Durali at MIT.</p> | ||
<p>Project published under a CERN-OHL license</p> | <p>According to the original development, the equipment would be used to feed an electrical network (coffee farm in South America), which is why they have selected a 60Hz generator, however, I believe that this can be adapted to the needs of whoever is going to replicate it. In any case, the same original design was followed.</p> | ||
<p>Project published under a CERN-OHL license.</p> | |||
|licence=COHL12 | |licence=COHL12 | ||
|typeproject=Web | |typeproject=Web | ||
| Line 61: | Line 64: | ||
|cmptitle=CAD Files | |cmptitle=CAD Files | ||
|cmpimage=Oseg swt render1.jpg | |cmpimage=Oseg swt render1.jpg | ||
|cmpfile1=Oseg swt CAD-files | |cmpfile1=Oseg swt CAD-files.zip | ||
|cmpfile2=Oseg swt | |cmpfile2=Oseg swt STP-files.zip | ||
}} | }} | ||
|Materials={{ProjektMaterials | |Materials={{ProjektMaterials | ||
| Line 71: | Line 72: | ||
|matdrawingsheet=A1 | |matdrawingsheet=A1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt A1 | |matpdffile=Oseg swt A1 Small water turbine.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=A2 | |matpartnumber=A2 | ||
|matdesc= | |matdesc=Presentation | ||
|matdrawingsheet=A2 | |matdrawingsheet=A2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt A2 small-water- | |matpdffile=Oseg swt A2 small-water-turbiner.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=B | |matpartnumber=B | ||
|matdesc= | |matdesc=Parts-list | ||
|matdrawingsheet=B | |matdrawingsheet=B | ||
|matpdffile=Oseg swt B | |matpdffile=Oseg swt B part-list.pdf | ||
|status_rev_1= | |status_rev_1=approved | ||
|status_rev_2=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=C | |||
|matdesc=Technical notes | |||
|matdrawingsheet=C | |||
|matspec=General notes | |||
|matpdffile=Oseg swt C technical-notes.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=1 | |matpartnumber=1 | ||
| Line 91: | Line 105: | ||
|matdrawingsheet=1 | |matdrawingsheet=1 | ||
|matparttype=production | |matparttype=production | ||
|status_rev_1= | |matspec=CAST IRON | ||
|matpdffile=Oseg swt 1.0 front adaptor.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=2 | |matpartnumber=2 | ||
|matposold=AF312 | |matposold=AF312 | ||
|matquantity=1 | |matquantity=1 | ||
|matdesc= | |matdesc=middle section | ||
|matdrawingsheet=2 | |matdrawingsheet=2 | ||
|matparttype=production | |matparttype=production | ||
|matspec=CAST IRON | |||
|matpdffile=Oseg swt 2.0 middle section.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3 | |matpartnumber=3 | ||
| Line 106: | Line 127: | ||
|matdrawingsheet=3 | |matdrawingsheet=3 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.0 drain | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.0 drain chute.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.1 | |matpartnumber=3.1 | ||
| Line 113: | Line 137: | ||
|matdrawingsheet=3.1 | |matdrawingsheet=3.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.1 back | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.1 back plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.2 | |matpartnumber=3.2 | ||
| Line 120: | Line 147: | ||
|matdrawingsheet=3.2 | |matdrawingsheet=3.2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.2 front | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.2 front flange.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.3 | |matpartnumber=3.3 | ||
| Line 127: | Line 157: | ||
|matdrawingsheet=3.3 | |matdrawingsheet=3.3 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.3 | |matspec=STEEL C45 | ||
|status_rev_1= | |matpdffile=Oseg swt 3.3 curved plate.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.4 | |matpartnumber=3.4 | ||
| Line 136: | Line 168: | ||
|matdrawingsheet=3.4 | |matdrawingsheet=3.4 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.4 side | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.4 side plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=3.5 | |matpartnumber=3.5 | ||
| Line 143: | Line 178: | ||
|matdrawingsheet=3.5 | |matdrawingsheet=3.5 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 3.5 front | |matspec=STEEL C45 | ||
|matpdffile=Oseg swt 3.5 front plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=4 | |matpartnumber=4 | ||
| Line 150: | Line 188: | ||
|matdrawingsheet=4 | |matdrawingsheet=4 | ||
|matparttype=production | |matparttype=production | ||
|matspec= | |matspec=See Technical notes | ||
|matpdffile=Oseg swt 4.0 | |matpdffile=Oseg swt 4.0 NOSE.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=5 | |matpartnumber=5 | ||
| Line 158: | Line 198: | ||
|matdrawingsheet=5 | |matdrawingsheet=5 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 5.0 | |matspec=See Technical notes | ||
|matpdffile=Oseg swt 5.0 STATOR BLADING.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=6 | |matpartnumber=6 | ||
| Line 165: | Line 208: | ||
|matdrawingsheet=6 | |matdrawingsheet=6 | ||
|matparttype=production | |matparttype=production | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=6.1 | |matpartnumber=6.1 | ||
| Line 170: | Line 215: | ||
|matdrawingsheet=6.1 | |matdrawingsheet=6.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 6.1 | |matspec=See Technical notes | ||
|matpdffile=Oseg swt 6.1 ROTOR BLADING.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=6.2 | |matpartnumber=6.2 | ||
| Line 176: | Line 224: | ||
|matdrawingsheet=6.2 | |matdrawingsheet=6.2 | ||
|matparttype=production | |matparttype=production | ||
|matspec=1,5 mm STEEL SHEET | |||
|matpdffile=Oseg swt 6.2 ROTOR WASHER.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=7 | |matpartnumber=7 | ||
| Line 182: | Line 234: | ||
|matdrawingsheet=7 | |matdrawingsheet=7 | ||
|matparttype=production | |matparttype=production | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=7.1 | |matpartnumber=7.1 | ||
| Line 187: | Line 241: | ||
|matdrawingsheet=7.1 | |matdrawingsheet=7.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 7.1 diffuser | |matspec=See Technical notes | ||
|matpdffile=Oseg swt 7.1 diffuser blanding.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=7.2 | |matpartnumber=7.2 | ||
| Line 193: | Line 250: | ||
|matdrawingsheet=7.2 | |matdrawingsheet=7.2 | ||
|matparttype=production | |matparttype=production | ||
|matspec=1,5 mm STEEL SHEET | |||
|matpdffile=Oseg swt 7.2 DIFFUSER WASHER.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=8 | |matpartnumber=8 | ||
| Line 199: | Line 260: | ||
|matdrawingsheet=8 | |matdrawingsheet=8 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 8.0 bush | |matspec=see tech. notes | ||
|matpdffile=Oseg swt 8.0 bush.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=9 | |matpartnumber=9 | ||
| Line 206: | Line 270: | ||
|matdrawingsheet=9 | |matdrawingsheet=9 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 9.0 | |matspec=ALUMINIUM | ||
|matpdffile=Oseg swt 9.0 slotter disk.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=10 | |matpartnumber=10 | ||
| Line 213: | Line 280: | ||
|matdrawingsheet=10 | |matdrawingsheet=10 | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=key 6 x 6 x 36.0 | |matspec=key 6 x 6 x 36.0, HARD STEEL | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11 | |matpartnumber=11 | ||
| Line 219: | Line 288: | ||
|matdrawingsheet=11 | |matdrawingsheet=11 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 11.0 hub | |matpdffile=Oseg swt 11.0 hub assembly.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.1 | |matpartnumber=11.1 | ||
| Line 226: | Line 297: | ||
|matdrawingsheet=11.1 | |matdrawingsheet=11.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 11.1 shaft | |matspec=STAINLESS STEEL | ||
|matpdffile=Oseg swt 11.1 shaft.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.2 | |matpartnumber=11.2 | ||
| Line 233: | Line 307: | ||
|matdrawingsheet=11.2 | |matdrawingsheet=11.2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 11.2 hub-housing | |matspec=CAST STEEL | ||
|matpdffile=Oseg swt 11.2 hub-housing.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.3 | |matpartnumber=11.3 | ||
| Line 240: | Line 317: | ||
|matdrawingsheet=11.3 | |matdrawingsheet=11.3 | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=1,5 mm STEEL SHEET | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.4 | |matpartnumber=11.4 | ||
| Line 247: | Line 327: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=bearing 206-SX adater and nut G-Y or equivalent estándar part | |matspec=bearing 206-SX adater and nut G-Y or equivalent estándar part | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.5 | |matpartnumber=11.5 | ||
| Line 253: | Line 335: | ||
|matdrawingsheet=11.5 | |matdrawingsheet=11.5 | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=GARLOCK 78*0542 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.6 | |matpartnumber=11.6 | ||
| Line 260: | Line 345: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=brownign 40P60 - 1/2" pich - 60 teeth - Dia.: 9.55" | |matspec=brownign 40P60 - 1/2" pich - 60 teeth - Dia.: 9.55" | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.7 | |matpartnumber=11.7 | ||
| Line 267: | Line 354: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=brownign Nº 4024 - 1/2" pich - 24 teeth - Dia.: 3.83" | |matspec=brownign Nº 4024 - 1/2" pich - 24 teeth - Dia.: 3.83" | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.8 | |matpartnumber=11.8 | ||
| Line 274: | Line 363: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=brownign Nº 40 - 1/2" pich Nº 40 | |matspec=brownign Nº 40 - 1/2" pich Nº 40 | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=11.9 | |matpartnumber=11.9 | ||
| Line 280: | Line 371: | ||
|matdrawingsheet=11.9 | |matdrawingsheet=11.9 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12 | |matpartnumber=12 | ||
| Line 286: | Line 379: | ||
|matdrawingsheet=12 | |matdrawingsheet=12 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.0 frame | |matpdffile=Oseg swt 12.0 frame.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12.1 | |matpartnumber=12.1 | ||
| Line 293: | Line 388: | ||
|matdrawingsheet=12.1 | |matdrawingsheet=12.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.1 side | |matspec=steel A36 | ||
|matpdffile=Oseg swt 12.1 side angle.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12.2 | |matpartnumber=12.2 | ||
| Line 300: | Line 398: | ||
|matdrawingsheet=12.2 | |matdrawingsheet=12.2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.2 top | |matspec=steel A36 | ||
|matpdffile=Oseg swt 12.2 top angle.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12.3 | |matpartnumber=12.3 | ||
| Line 307: | Line 408: | ||
|matdrawingsheet=12.3 | |matdrawingsheet=12.3 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.3 top | |matspec=steel A36 | ||
|matpdffile=Oseg swt 12.3 top plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12.4 | |matpartnumber=12.4 | ||
|matposold=AF3227D | |matposold=AF3227D | ||
|matdesc=bar | |matdesc=bar plate | ||
|matdrawingsheet=12.4 | |matdrawingsheet=12.4 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.4 bar | |matspec=steel A36 | ||
|matpdffile=Oseg swt 12.4 bar plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=12.5 | |matpartnumber=12.5 | ||
| Line 321: | Line 428: | ||
|matdrawingsheet=12.5 | |matdrawingsheet=12.5 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 12.5 fundation | |matspec=steel A36 | ||
|matpdffile=Oseg swt 12.5 fundation plate.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13 | |matpartnumber=13 | ||
| Line 328: | Line 438: | ||
|matdrawingsheet=13 | |matdrawingsheet=13 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 13.0 oil | |matpdffile=Oseg swt 13.0 oil bath.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13.1 | |matpartnumber=13.1 | ||
| Line 334: | Line 446: | ||
|matdrawingsheet=13.1 | |matdrawingsheet=13.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 13.1 plate | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 13.1 plate front cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13.2 | |matpartnumber=13.2 | ||
| Line 340: | Line 455: | ||
|matdrawingsheet=13.2 | |matdrawingsheet=13.2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 13.2 band | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 13.2 band side cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13.3 | |matpartnumber=13.3 | ||
| Line 346: | Line 464: | ||
|matdrawingsheet=13.3 | |matdrawingsheet=13.3 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile= | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 13.3 plate down cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13.4 | |matpartnumber=13.4 | ||
| Line 352: | Line 473: | ||
|matdrawingsheet=13.4 | |matdrawingsheet=13.4 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 13.4 brake | |matspec=STEEL A36 | ||
|matpdffile=Oseg swt 13.4 brake angle cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=13.5 | |matpartnumber=13.5 | ||
| Line 358: | Line 482: | ||
|matdrawingsheet=13.5 | |matdrawingsheet=13.5 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 13.5 brake | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 13.5 brake bar cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=14 | |matpartnumber=14 | ||
| Line 365: | Line 492: | ||
|matdrawingsheet=14 | |matdrawingsheet=14 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 14.0 back | |matpdffile=Oseg swt 14.0 back oil bath.pdf | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=14.1 | |matpartnumber=14.1 | ||
| Line 371: | Line 500: | ||
|matdrawingsheet=14.1 | |matdrawingsheet=14.1 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 14.1 plate | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 14.1 plate back cover.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=14.2 | |matpartnumber=14.2 | ||
| Line 377: | Line 509: | ||
|matdrawingsheet=14.2 | |matdrawingsheet=14.2 | ||
|matparttype=production | |matparttype=production | ||
|matpdffile=Oseg swt 14.2 | |matspec=2-3 MM STEEL SHEET | ||
|matpdffile=Oseg swt 14.2 bar for plate front.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=15 | |matpartnumber=15 | ||
| Line 385: | Line 520: | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=5 KW; 115-230 V;21,5 A; 60Hz | |matspec=5 KW; 115-230 V;21,5 A; 60Hz | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=16 | |matpartnumber=16 | ||
| Line 392: | Line 529: | ||
|matdrawingsheet=16 | |matdrawingsheet=16 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=17 | |matpartnumber=17 | ||
| Line 399: | Line 538: | ||
|matdrawingsheet=17 | |matdrawingsheet=17 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=18 | |matpartnumber=18 | ||
| Line 406: | Line 547: | ||
|matdrawingsheet=18 | |matdrawingsheet=18 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=19 | |matpartnumber=19 | ||
| Line 413: | Line 556: | ||
|matdrawingsheet=19 | |matdrawingsheet=19 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=20 | |matpartnumber=20 | ||
| Line 420: | Line 565: | ||
|matdrawingsheet=20 | |matdrawingsheet=20 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=21 | |matpartnumber=21 | ||
| Line 427: | Line 574: | ||
|matdrawingsheet=21 | |matdrawingsheet=21 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=22 | |matpartnumber=22 | ||
| Line 434: | Line 583: | ||
|matdrawingsheet=22 | |matdrawingsheet=22 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=23 | |matpartnumber=23 | ||
| Line 441: | Line 592: | ||
|matdrawingsheet=23 | |matdrawingsheet=23 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=24 | |matpartnumber=24 | ||
| Line 448: | Line 601: | ||
|matdrawingsheet=24 | |matdrawingsheet=24 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=25 | |matpartnumber=25 | ||
| Line 455: | Line 610: | ||
|matdrawingsheet=25 | |matdrawingsheet=25 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=26 | |matpartnumber=26 | ||
| Line 462: | Line 619: | ||
|matdrawingsheet=26 | |matdrawingsheet=26 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=27 | |matpartnumber=27 | ||
| Line 469: | Line 628: | ||
|matdrawingsheet=27 | |matdrawingsheet=27 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=28 | |matpartnumber=28 | ||
| Line 476: | Line 637: | ||
|matdrawingsheet=28 | |matdrawingsheet=28 | ||
|matparttype=standard | |matparttype=standard | ||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}}{{ProjektMaterials | }}{{ProjektMaterials | ||
|matpartnumber=29 | |matpartnumber=29 | ||
| Line 483: | Line 646: | ||
|matdrawingsheet=29 | |matdrawingsheet=29 | ||
|matparttype=standard | |matparttype=standard | ||
|matspec=HARD STEEL | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
}} | }} | ||
|certificate_requested=No | |certificate_requested=No | ||
|certificate_status=in process | |certificate_status=in process | ||
|reviewer1=Xtech2020 review | |reviewer1=Xtech2020 review | ||
|reviewer2=Thehunter | |||
}} | }} | ||
Revision as of 01:01, 7 April 2021
|
Small water turbine Basic Data Category: Small Water turbines URL (first publication): https://dspace.mit.edu/handle/1721.1/27493 Keywords: turbine, hidraulic, turbomachinery, water, renewable, sustainable, electric power, mit License: CERN OHL v1.2 Organization: Practical Action Project status: Active Certification status: In process Technical documentation Maturity of the project: prototype
Contains PDF-drawings: Yes Assembly instructions are published: No Bill of materials is published: Yes
yes yes
|
|
Description
This project shows the construction plans for a small 5 kW water turbine based on the research of Dr. Mohammad Durali at MIT.
According to the original development, the equipment would be used to feed an electrical network (coffee farm in South America), which is why they have selected a 60Hz generator, however, I believe that this can be adapted to the needs of whoever is going to replicate it. In any case, the same original design was followed.
Project published under a CERN-OHL license.
Technical documentation
PDF Plans | |
|
|
Files: | |
CAD Files | |
|
|
Files: | |
+ General Reviews 
Parts list
| Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
|---|---|---|---|---|---|---|---|---|
| A1 | small water turbine | A1 | Production |
REV1: Approved |
|
|||
| A2 | Presentation | A2 | Production |
REV1: Approved |
|
|||
| B | Parts-list | B |
REV1: Approved |
|
||||
| C | Technical notes | C | General notes |
REV1: Approved |
|
|||
| 1 | 1 | front adaptor | 1 | Production | CAST IRON |
REV1: Approved |
|
|
| 2 | 1 | middle section | 2 | Production | CAST IRON |
REV1: Approved |
|
|
| 3 | 1 | drain chute | 3 | Production | STEEL C45 |
REV1: Approved |
|
|
| 3.1 | back plate | 3.1 | Production | STEEL C45 |
REV1: Approved |
|
||
| 3.2 | front flange | 3.2 | Production | STEEL C45 |
REV1: Approved |
|
||
| 3.3 | curved plate | 3.3 | Production | STEEL C45 |
REV1: Approved |
|
||
| 3.4 | 2 | side plate | 3.4 | Production | STEEL C45 |
REV1: Approved |
|
|
| 3.5 | front plate | 3.5 | Production | STEEL C45 |
REV1: Approved |
|
||
| 4 | nose | 4 | Production | See Technical notes |
REV1: Approved |
|
||
| 5 | stator blading | 5 | Production | See Technical notes |
REV1: Approved |
|
||
| 6 | rotor blading | 6 | Production |
REV1: Approved |
|
|||
| 6.1 | rotor blading | 6.1 | Production | See Technical notes |
REV1: Approved |
|
||
| 6.2 | rotor washer | 6.2 | Production | 1,5 mm STEEL SHEET |
REV1: Approved |
|
||
| 7 | diffuser blanding | 7 | Production |
REV1: Approved |
|
|||
| 7.1 | diffuser blanding | 7.1 | Production | See Technical notes |
REV1: Approved |
|
||
| 7.2 | diffuser washer | 7.2 | Production | 1,5 mm STEEL SHEET |
REV1: Approved |
|
||
| 8 | bush | 8 | Production | see tech. notes |
REV1: Approved |
|
||
| 9 | slotted disk | 9 | Production | ALUMINIUM |
REV1: Approved |
|
||
| 10 | key | 10 | Standard | key 6 x 6 x 36.0, HARD STEEL |
REV1: Approved |
|
||
| 11 | Transmission (hub assembly) | 11 | Production |
REV1: Approved |
|
|||
| 11.1 | shaft | 11.1 | Production | STAINLESS STEEL |
REV1: Approved |
|
||
| 11.2 | hub housing | 11.2 | Production | CAST STEEL |
REV1: Approved |
|
||
| 11.3 | front cap | 11.3 | Standard | 1,5 mm STEEL SHEET |
REV1: Approved |
|
||
| 11.4 | ball bearing | 11.4 | Standard | bearing 206-SX adater and nut G-Y or equivalent estándar part |
REV1: Approved |
|
||
| 11.5 | seal | 11.5 | Standard | GARLOCK 78*0542 |
REV1: Approved |
|
||
| 11.6 | big sprocket | 11.6 | Standard | brownign 40P60 - 1/2" pich - 60 teeth - Dia.: 9.55" |
REV1: Approved |
|
||
| 11.7 | small sprocket | 11.7 | Standard | brownign Nº 4024 - 1/2" pich - 24 teeth - Dia.: 3.83" |
REV1: Approved |
|
||
| 11.8 | chain | 11.8 | Standard | brownign Nº 40 - 1/2" pich Nº 40 |
REV1: Approved |
|
||
| 11.9 | bolt 3/16" x 32 x 5/16" | 11.9 | Standard |
REV1: Approved |
|
|||
| 12 | frame | 12 | Production |
REV1: Approved |
|
|||
| 12.1 | side angles | 12.1 | Production | steel A36 |
REV1: Approved |
|
||
| 12.2 | top angle | 12.2 | Production | steel A36 |
REV1: Approved |
|
||
| 12.3 | top plate | 12.3 | Production | steel A36 |
REV1: Approved |
|
||
| 12.4 | bar plate | 12.4 | Production | steel A36 |
REV1: Approved |
|
||
| 12.5 | foundation plate | 12.5 | Production | steel A36 |
REV1: Approved |
|
||
| 13 | oil bath cover | 13 | Production |
REV1: Approved |
|
|||
| 13.1 | plate front cover | 13.1 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|
||
| 13.2 | band side cover | 13.2 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|
||
| 13.3 | plate down cover | 13.3 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|
||
| 13.4 | brake angle cover | 13.4 | Production | STEEL A36 |
REV1: Approved |
|
||
| 13.5 | brake bar cover | 13.5 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|
||
| 14 | back oil bath cover | 14 | Production |
REV1: Approved |
|
|||
| 14.1 | plate back cover | 14.1 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|
||
| 14.2 | bar for plate front | 14.2 | Production | 2-3 MM STEEL SHEET |
REV1: Approved |
|
||
| 15 | Generator | 15 | Standard | 5 KW; 115-230 V;21,5 A; 60Hz |
REV1: Approved |
|
||
| 16 | 20 | bolt 5/8"x12 - 2 1/2" | 16 | Standard |
REV1: Approved |
|
||
| 17 | 20 | nut 5/8"x12 | 17 | Standard |
REV1: Approved |
|
||
| 18 | 20 | plain washer 5/8" | 18 | Standard |
REV1: Approved |
|
||
| 19 | 4 | bolt 1/2"x12 - 1 1/2" | 19 | Standard |
REV1: Approved |
|
||
| 20 | 4 | nut 1/2"x12 | 20 | Standard |
REV1: Approved |
|
||
| 21 | 4 | plain washer 1/2" | 21 | Standard |
REV1: Approved |
|
||
| 22 | 4 | bolt 9/16"x12 - 2" | 22 | Standard |
REV1: Approved |
|
||
| 23 | 4 | nut 9/16"x12 | 23 | Standard |
REV1: Approved |
|
||
| 24 | 4 | plain washer 9/16" | 24 | Standard |
REV1: Approved |
|
||
| 25 | 4 | lock washer 9/16" | 25 | Standard |
REV1: Approved |
|
||
| 26 | 1 | bolt 3/8"x16 - 2" | 26 | Standard |
REV1: Approved |
|
||
| 27 | 2 | wing nut 3/8"x16 | 27 | Standard |
REV1: Approved |
|
||
| 28 | 1 | plain washer 3/8" | 28 | Standard |
REV1: Approved |
|
||
| 29 | 4 | ALIGNMENT-PIN | 29 | Standard | HARD STEEL |
REV1: Approved |
|
|