Difference between revisions of "Segner Turbine for 4m Pit"
Line 50: | Line 50: | ||
|cmpfile2=Skt st4 DWG-files .zip | |cmpfile2=Skt st4 DWG-files .zip | ||
|cmpfile3=Skt st4 STP-files .zip | |cmpfile3=Skt st4 STP-files .zip | ||
}}{{ProjektComponent | |||
|cmptitle=Attestation | |||
|cmpimage=Attestation Segner Turbine for 4m Pit.jpg | |||
|cmpimg=e project Segner Turbine for 4m Pit was reviewed by two reviewers from the OHO team. The review consisted of the following components: | |||
1. Completeness check: Checks if all required documents have been submitted. | |||
2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. | |||
2.1 Bill of materials | |||
- Are all parts and assemblies covered? | |||
- Are all quantities correct? | |||
- Are all required material specifications available? | |||
- Are all specifications for purchased parts and standard parts complete? | |||
3.2 Technical drawings | |||
- Are all the required views available? | |||
- Are all required dimensional data available? | |||
4.1 Suggestions for improvement | |||
Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers | |||
Permanent Link: https://en.oho.wiki/index.php?title=Segner_Turbine_for_4m_Pit&oldid=44355 | |||
|cmpfile1=Attestation Segner Turbine for 4m Pit .pdf | |||
}} | }} | ||
|Materials={{ProjektMaterials | |Materials={{ProjektMaterials |
Revision as of 09:31, 18 January 2022
Segner Turbine for 4m Pit Basic Data Category: Water turbines Keywords: segner, turbine, diy, oho License: CC BY-SA 4.0 Organization: SKAT, Switzerland Project status: Active Certification status: In process Technical documentation
Contains PDF-drawings: Yes CAD files are editable: Yes Assembly instructions are published: No Bill of materials is published: Yes
yes yes
|
|
Technical documentation
Complete PDF plans | |
Files: |
CAD files | |
Files: |
Attestation | |
e project Segner Turbine for 4m Pit was reviewed by two reviewers from the OHO team. The review consisted of the following components:
1. Completeness check: Checks if all required documents have been submitted. 2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. 2.1 Bill of materials - Are all parts and assemblies covered? - Are all quantities correct? - Are all required material specifications available? - Are all specifications for purchased parts and standard parts complete? 3.2 Technical drawings - Are all the required views available? - Are all required dimensional data available? 4.1 Suggestions for improvement Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers Permanent Link: https://en.oho.wiki/index.php?title=Segner_Turbine_for_4m_Pit&oldid=44355 | |
Files: |
+ General Reviews
Parts list
Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
---|---|---|---|---|---|---|---|---|
A1 | 1 | 3D views | - |
REV1: Approved |
||||
A2 | 1 | Exploded 3d view | - |
REV1: Approved |
||||
B1 | - | Parts list | - |
REV1: Approved |
||||
C1 | - | Technical notes | - |
REV1: Action required |
||||
1.0 | 1 | Rotor | - |
REV1: Approved |
||||
1.1 | 1 | Vertical pipe A | Production | Galvanized steel sch20 pipe d:14 variable length |
REV1: Approved |
|||
1.2 | 4 | Connector ring A | Production | Galvanized steel 1.5mm |
REV1: Approved |
|||
1.3 | 1 | Funnel | Production | Galvanized steel 1.5mm |
REV1: Approved |
|||
1.4 | 1 | Vertical tube B | Production | Galvanized steel |
REV1: Approved |
|||
1.5 | 1 | Lower cap | Production | Galvanized steel 1.5mm |
REV1: Approved |
|||
1.6 | 4 | Blade A | Production | Galvanized steel platen 3x25x150mm |
REV1: Approved |
|||
1.7 | 4 | Blade B | Production | Galvanized steel platen 3x25mm |
REV1: Approved |
|||
1.8 | 2 | Radial pipe A | Production | Galvanized steel sch20 pipe d:3 1/2 L:500mm |
REV1: Approved |
|||
1.9 | 2 | Elbow | Buy | Galvanized steel sch20 elbow d:3 1/2 |
REV1: Approved |
|||
1.10 | 2 | Radial pipe A | Production | Galvanized steel sch20 pipe d:3 1/2 L:300mm |
REV1: Approved |
|||
1.11 | 2 | Connector ring B | Production | Galvanized steel 1.5mm |
REV1: Approved |
|||
1.12 | 2 | Nozzle | Production | Galvanized steel 1.5mm |
REV1: Approved |
|||
1.13 | 12 | Screw A | Standard | DIN 8676 M8x16mm |
REV1: Approved |
|||
1.14 | 12 | Nut A | Standard | DIN 28674 M8 |
REV1: Approved |
|||
1.15 | 1 | Shaft A | Production | Steel C45 hardened d:45mm |
REV1: Approved |
|||
1.16 | 1 | Ball bearing | Buy | Stainless steel bearing ID25mm ultra sealed (NSK or similar) |
REV1: Approved |
|||
1.17 | 1 | Base plate | Production | Galvanized steel 3mm |
REV1: Approved |
|||
1.18 | 1 | Groove Pulley A | Buy | Bore single groove ID25mm, ED250mm |
REV1: Approved |
|||
2.0 | 1 | Line shaft | - |
REV1: Approved |
||||
2.1 | 2 | Foot | Production | Hardwood 25x25x500mm |
REV1: Approved |
|||
2.2 | 2 | Wooden connector | Production | Hardwood 20x30mm |
REV1: Approved |
|||
2.3 | 2 | Pillow block | Buy | Cast iron pillow block, shaft 24mm |
REV1: Approved |
|||
2.4 | 4 | Screw B | Standard | DIN 8676 M8x40mm |
REV1: Approved |
|||
2.5 | 4 | Nut B | Standard | DIN 28674 M8 |
REV1: Approved |
|||
2.6 | 1 | Shaft B | Production | Steel C45 hardened d:24mm |
REV1: Approved |
|||
2.7 | 2 | Groove Pulley B | Buy | Bore single groove ID24mm, ED100mm |
REV1: Approved |
|||
2.8 | 2 | Circlip | Standard | DIN 472 24mm |
REV1: Approved |
|||
2.9 | 1 | Belt | Buy | Belt 20mm variable length |
REV1: Approved |
|||
3.0 | 1 | Channel | - |
REV1: Approved |
||||
3.1 | 2 | Channel sheet A | Production | Galvanized steel sheet 1.5x400x1500mm |
REV1: Approved |
|||
3.2 | 1 | Channel sheet B | Production | Galvanized steel sheet 1.5x400x500mm |
REV1: Approved |
|||
3.3 | 1 | Channel sheet C | Production | Galvanized steel sheet 1.5x500x1000mm |
REV1: Approved |
|||
3.4 | 4 | Channel sheet D | Production | Galvanized steel sheet 1.5mm |
REV1: Approved |
|||
3.5 | 2 | Stiffener | Production | Steel A36 angle 3x30x30x1000mm |
REV1: Approved |
|||
3.6 | 2 | Gate plate A | Production | Steel A36 platen 3x30x374mm |
REV1: Approved |
|||
3.7 | 1 | Gate plate B | Production | Steel A36 angle 3x30x500mm |
REV1: Approved |
|||
3.8 | 1 | Gate bar | Production | Steel C45 circular bar d:10mm L:496mm threaded |
REV1: Approved |
|||
3.9 | 1 | Gate handle | Production | Steel C45 circular bar d:10mm L:200mm |
REV1: Approved |
|||
3.10 | 1 | Nut C | Standard | DIN 28674 M10 |
REV1: Approved |
|||
4.0 | 1 | Frame | - |
REV1: Approved |
||||
4.1 | 2 | Bar A | Production | Steel A36 square bar 12x12mm |
REV1: Approved |
|||
4.2 | 2 | Bar B | Production | Steel A36 square bar 12x12x488mm |
REV1: Approved |
|||
4.3 | 2 | Bar C | Production | Steel A36 square bar 12x12mm |
REV1: Approved |
|||
4.4 | 2 | Bar D | Production | Steel A36 square bar 12x12mm |
REV1: Approved |
|||
4.5 | 2 | Bar E | Production | Steel A36 square bar 12x12mm |
REV1: Approved |
|||
4.6 | 1 | Bar F | Production | Steel A36 square bar 12x12x82mm |
REV1: Approved |
|||
4.7 | 1 | Bar G | Production | Steel A36 square bar 12x12mm |
REV1: Action required |
|||