Difference between revisions of "Savonius Rotor with Two Blade Levels"
(Created page with "{{Projekt |Images={{ProjektImages |projectimage=Hs srl savonius-rotor-two-level 0001.jpg }}{{ProjektImages |projectimage=Hs srl savonius-rotor-two-level 0002.jpg }}{{ProjektIm...") |
|||
(9 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
{{Projekt | {{Projekt | ||
|Images={{ProjektImages | |Images={{ProjektImages | ||
|projectimage=Savonius.png | |||
}}{{ProjektImages | |||
|projectimage=Hs srl savonius-rotor-two-level 0001.jpg | |projectimage=Hs srl savonius-rotor-two-level 0001.jpg | ||
}}{{ProjektImages | }}{{ProjektImages | ||
Line 25: | Line 27: | ||
|subcat=Savonius wind turbines | |subcat=Savonius wind turbines | ||
|projectname=Savonius Rotor with Two Blade Levels | |projectname=Savonius Rotor with Two Blade Levels | ||
|projectnameES=Rotor Savonius con dos | |projectnameES=Rotor Savonius con dos Niveles de Palas | ||
|projectnameDE=Savonius-Rotor mit zwei Bildebenen | |projectnameDE=Savonius-Rotor mit zwei Bildebenen | ||
|kewords=savonius, rotor, two, blade, levels, diy, oho | |kewords=savonius, rotor, two, blade, levels, diy, oho | ||
Line 51: | Line 53: | ||
|cmptitle=CAD files | |cmptitle=CAD files | ||
|cmpimage=Hs srl savonius-rotor-two-level 0001.jpg | |cmpimage=Hs srl savonius-rotor-two-level 0001.jpg | ||
|cmpfile1=Hs srl CAD-files.zip | |||
|cmpfile2=Hs srl DWG-files.zip | |||
|cmpfile3=Hs srl STP-files.zip | |||
}}{{ProjektComponent | |||
|cmptitle=Attestation | |||
|cmpimage=Attestation Savonius rotor with two blade levels.jpg | |||
|cmpimg=The project Savonius rotor with two blade levels was reviewed by two reviewers from the OHO team. The review consisted of the following components: | |||
1. Completeness check: Checks if all required documents have been submitted. | |||
2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. | |||
2.1 Bill of materials | |||
- Are all parts and assemblies covered? | |||
- Are all quantities correct? | |||
- Are all required material specifications available? | |||
- Are all specifications for purchased parts and standard parts complete? | |||
3.2 Technical drawings | |||
- Are all the required views available? | |||
- Are all required dimensional data available? | |||
4.1 Suggestions for improvement | |||
Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers | |||
Permanent Link: https://en.oho.wiki/index.php?title=Savonius_Rotor_with_Two_Blade_Levels&oldid=44313 | |||
|cmpfile1=Attestation Savonius rotor with two blade levels.pdf | |||
}} | |||
|Materials={{ProjektMaterials | |||
|matpartnumber=A1 | |||
|matquantity=1 | |||
|matdesc=3D views | |||
|matpdffile=Hs srl savonius-rotor-two-level A1.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=A2 | |||
|matquantity=1 | |||
|matdesc=3D Explode | |||
|matpdffile=Hs srl savonius-rotor-two-level A2.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=B1 | |||
|matdesc=Parts list | |||
|matpdffile=Hs srl savonius-rotor-two-level B1.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=C1 | |||
|matdesc=Technical notes | |||
|matpdffile=Hs srl savonius-rotor-two-level C1.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.0 | |||
|matquantity=1 | |||
|matdesc=Rotor | |||
|matpdffile=Hs srl savonius-rotor-two-leve 1.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.1 | |||
|matquantity=4 | |||
|matdesc=Sheet | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 1.1.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.2 | |||
|matquantity=3 | |||
|matdesc=Plates plywood | |||
|matparttype=production | |||
|matspec=Plywood | |||
|matpdffile=Hs srl savonius-rotor-two-level 1.2.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.3 | |||
|matquantity=20 | |||
|matdesc=Roller shutter | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 1.3 .pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.4 | |||
|matquantity=3 | |||
|matdesc=Flange support | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 1.4 .pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.5 | |||
|matquantity=1 | |||
|matdesc=Tube central | |||
|matparttype=production | |||
|matspec=Schd 40, ASTM A36 | |||
|matpdffile=Hs srl savonius-rotor-two-level 1.5.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.6 | |||
|matquantity=1 | |||
|matdesc=Shaft support | |||
|matparttype=production | |||
|matspec=Pipe Schd 40, Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 1.6.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.7 | |||
|matquantity=1 | |||
|matdesc=Shaft upper | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 1.7.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.8 | |||
|matquantity=1 | |||
|matdesc=Shaft middle | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 1.8.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.9 | |||
|matquantity=4 | |||
|matdesc=Clamping-bar | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 1.9.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.10 | |||
|matquantity=180 | |||
|matdesc=Bolt plate | |||
|matparttype=standard | |||
|matspec=Bolt plate, Hex M6 DIN-934 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.11 | |||
|matquantity=180 | |||
|matdesc=Nut plate | |||
|matparttype=standard | |||
|matspec=Nut plate, Hex M6 DIN-934 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.12 | |||
|matquantity=4 | |||
|matdesc=Bolt Shaft | |||
|matparttype=standard | |||
|matspec=Bolt Shaft, Hex M10 DIN-934 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=1.13 | |||
|matquantity=4 | |||
|matdesc=Nut Shaft | |||
|matparttype=standard | |||
|matspec=Nut Shaft, Hex M10 DIN-934 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.0 | |||
|matquantity=1 | |||
|matdesc=Frame | |||
|matpdffile=Hs srl savonius-rotor-two-level 2.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.1 | |||
|matquantity=2 | |||
|matdesc=Pole vertical | |||
|matparttype=production | |||
|matspec=Schd 40, ASTM A36 | |||
|matpdffile=Hs srl savonius-rotor-two-level 2.1.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.2 | |||
|matquantity=1 | |||
|matdesc=Pole long horzt | |||
|matparttype=production | |||
|matspec=Schd 40, ASTM A36 | |||
|matpdffile=Hs srl savonius-rotor-two-level 2.2.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.3 | |||
|matquantity=1 | |||
|matdesc=Pole short horzt | |||
|matparttype=production | |||
|matspec=Schd 40, ASTM A36 | |||
|matpdffile=Hs srl savonius-rotor-two-level 2.3.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.4 | |||
|matquantity=2 | |||
|matdesc=Pipe a 45� | |||
|matparttype=production | |||
|matspec=Schd 40, ASTM A36 | |||
|matpdffile=Hs srl savonius-rotor-two-level 2.4.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.5 | |||
|matquantity=1 | |||
|matdesc=Support generator | |||
|matparttype=production | |||
|matspec=Sheet metal t:3mm, ASTM A36 | |||
|matpdffile=Hs srl savonius-rotor-two-level 2.5.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.6 | |||
|matquantity=2 | |||
|matdesc=Base bearing | |||
|matparttype=production | |||
|matspec=ASTM A36 | |||
|matpdffile=Hs srl savonius-rotor-two-level 2.6.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.7 | |||
|matquantity=2 | |||
|matdesc=Flange Bearing | |||
|matparttype=standard | |||
|matspec=Flange Bearing, square flange UCF206D1 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.8 | |||
|matquantity=2 | |||
|matdesc=Flange axial Bearin | |||
|matparttype=standard | |||
|matspec=Flange axial bearing, UCF207D1 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=2.9 | |||
|matquantity=12 | |||
|matdesc=Bolt for bearing | |||
|matparttype=standard | |||
|matspec=Bolt for bearing, Hex M10 DIN-934 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.0 | |||
|matquantity=1 | |||
|matdesc=Transmission | |||
|matpdffile=Hs srl savonius-rotor-two-level 3.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.1 | |||
|matquantity=1 | |||
|matdesc=Working Shaft | |||
|matparttype=production | |||
|matspec=Schd 40, ASTM A36 | |||
|matpdffile=Hs srl savonius-rotor-two-level 3.1.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.2 | |||
|matquantity=1 | |||
|matdesc=Shaft support | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 3.2.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.3 | |||
|matquantity=1 | |||
|matdesc=Shaft lower | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 3.3.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.4 | |||
|matquantity=1 | |||
|matdesc=Base motor | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 3.4.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.5 | |||
|matquantity=1 | |||
|matdesc=Fly wheel small | |||
|matparttype=standard | |||
|matspec=Fly wheel small, D: 75.0 x 1 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.6 | |||
|matquantity=1 | |||
|matdesc=Fly wheel medium | |||
|matparttype=standard | |||
|matspec=Fly wheel medium, D:150 x1 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.7 | |||
|matquantity=1 | |||
|matdesc=Belt trans | |||
|matparttype=standard | |||
|matspec=Belt trans, type V | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.8 | |||
|matquantity=1 | |||
|matdesc=Generator | |||
|matparttype=standard | |||
|matspec=Generator | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.9 | |||
|matquantity=4 | |||
|matdesc=Bolt 1 | |||
|matparttype=standard | |||
|matspec=Bolt 1, Hex M10 x 50 DIN 934 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.10 | |||
|matquantity=3 | |||
|matdesc=Bolt 2 | |||
|matparttype=standard | |||
|matspec=Bolt 2, Hex M10 x 70 DIN 934 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=3.11 | |||
|matquantity=7 | |||
|matdesc=Nut | |||
|matparttype=standard | |||
|matspec=Nut, Hex M10 DIN 934 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=4.0 | |||
|matquantity=4 | |||
|matdesc=Tensioner | |||
|matparttype=production | |||
|matpdffile=Hs srl savonius-rotor-two-level 4.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=4.1 | |||
|matquantity=4 | |||
|matdesc=. Angle25 | |||
|matparttype=production | |||
|matspec=ASTM A36 | |||
|matpdffile=Hs srl savonius-rotor-two-level 4.1.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=4.2 | |||
|matquantity=4 | |||
|matdesc=Turnbuckles | |||
|matparttype=standard | |||
|matspec=Turnbuckles, tensioner for guy of 6 mm | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=4.3 | |||
|matquantity=8 | |||
|matdesc=Rulldog grips | |||
|matparttype=standard | |||
|matspec=Rulldog grips, Grip 4 mm to 12mm cap. include nut and washer | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=4.4 | |||
|matquantity=4 | |||
|matdesc=guy wire | |||
|matparttype=production | |||
|matspec=wire of D: 6mm - total:4,60 m, Galvanized steel | |||
|matpdffile=Hs srl savonius-rotor-two-level 4.4.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=5.0 | |||
|matquantity=1 | |||
|matdesc=Parking brake | |||
|matpdffile=Hs srl savonius-rotor-two-level 5.0.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=5.1 | |||
|matquantity=1 | |||
|matdesc=Break arm | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 5.1.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=5.2 | |||
|matquantity=2 | |||
|matdesc=Arm pivote | |||
|matparttype=standard | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 5.2.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=5.3 | |||
|matquantity=1 | |||
|matdesc=Arm pivote2 | |||
|matparttype=production | |||
|matspec=Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 5.3.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=5.4 | |||
|matquantity=1 | |||
|matdesc=Grader plate | |||
|matparttype=production | |||
|matspec=Production Steel C45 | |||
|matpdffile=Hs srl savonius-rotor-two-level 5.4.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=5.5 | |||
|matquantity=1 | |||
|matdesc=Brake cable | |||
|matparttype=production | |||
|matspec=Production guy L:2,20 m, Galvanized steel | |||
|matpdffile=Hs srl savonius-rotor-two-level 5.5.pdf | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=5.6 | |||
|matquantity=2 | |||
|matdesc=Rulldog grips | |||
|matparttype=standard | |||
|matspec=Standard Rulldog grips, for guy D:6.0mm | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=5.7 | |||
|matquantity=1 | |||
|matdesc=Spring | |||
|matparttype=standard | |||
|matspec=Standard Spring, 20x90x4 | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}}{{ProjektMaterials | |||
|matpartnumber=5.8 | |||
|matquantity=1 | |||
|matdesc=Bolt pin | |||
|matparttype=standard | |||
|matspec=Standard Bolt pin | |||
|status_rev_1=approved | |||
|status_rev_2=approved | |||
|status_rev_3=approved | |||
}} | }} | ||
|certificate_requested=No | |certificate_requested=No | ||
|certificate_status=approved | |||
|reviewer1=Dmosquera1968 | |||
|reviewer2=Jaimerosciano | |||
|reviewer3=Jeefri | |||
}} | }} |
Latest revision as of 07:34, 4 February 2022
Savonius Rotor with Two Blade Levels Basic Data Category: Savonius wind turbines Keywords: savonius, rotor, two, blade, levels, diy, oho License: CC BY-SA 4.0 Organization: Heinz Schulz Project status: Active Certification status: Approved Technical documentation
Contains PDF-drawings: Yes CAD files are editable: Yes Assembly instructions are published: No Bill of materials is published: Yes
yes yes
|
|
Technical documentation
Complete PDF plans | |
Files: |
CAD files | |
Files: |
Attestation | |
The project Savonius rotor with two blade levels was reviewed by two reviewers from the OHO team. The review consisted of the following components:
1. Completeness check: Checks if all required documents have been submitted. 2. Review of the submitted documents: Checks if the information in the submitted documents is complete and correct. 2.1 Bill of materials - Are all parts and assemblies covered? - Are all quantities correct? - Are all required material specifications available? - Are all specifications for purchased parts and standard parts complete? 3.2 Technical drawings - Are all the required views available? - Are all required dimensional data available? 4.1 Suggestions for improvement Detail abot the review process: https://en.oho.wiki/wiki/Instructions_for_Reviewers Permanent Link: https://en.oho.wiki/index.php?title=Savonius_Rotor_with_Two_Blade_Levels&oldid=44313 | |
Files: |
+ General Reviews
Parts list
Pos. | Qty. | Part Name | Part code | Part Type | Specifications | Review Status | Show All Comments | |
---|---|---|---|---|---|---|---|---|
A1 | 1 | 3D views |
REV1: Approved |
|||||
A2 | 1 | 3D Explode |
REV1: Approved |
|||||
B1 | Parts list |
REV1: Approved |
||||||
C1 | Technical notes |
REV1: Approved |
||||||
1.0 | 1 | Rotor |
REV1: Approved |
|||||
1.1 | 4 | Sheet | Production | Steel C45 |
REV1: Approved |
|||
1.2 | 3 | Plates plywood | Production | Plywood |
REV1: Approved |
|||
1.3 | 20 | Roller shutter | Production | Steel C45 |
REV1: Approved |
|||
1.4 | 3 | Flange support | Production | Steel C45 |
REV1: Approved |
|||
1.5 | 1 | Tube central | Production | Schd 40, ASTM A36 |
REV1: Approved |
|||
1.6 | 1 | Shaft support | Production | Pipe Schd 40, Steel C45 |
REV1: Approved |
|||
1.7 | 1 | Shaft upper | Production | Steel C45 |
REV1: Approved |
|||
1.8 | 1 | Shaft middle | Production | Steel C45 |
REV1: Approved |
|||
1.9 | 4 | Clamping-bar | Production | Steel C45 |
REV1: Approved |
|||
1.10 | 180 | Bolt plate | Standard | Bolt plate, Hex M6 DIN-934 |
REV1: Approved |
|||
1.11 | 180 | Nut plate | Standard | Nut plate, Hex M6 DIN-934 |
REV1: Approved |
|||
1.12 | 4 | Bolt Shaft | Standard | Bolt Shaft, Hex M10 DIN-934 |
REV1: Approved |
|||
1.13 | 4 | Nut Shaft | Standard | Nut Shaft, Hex M10 DIN-934 |
REV1: Approved |
|||
2.0 | 1 | Frame |
REV1: Approved |
|||||
2.1 | 2 | Pole vertical | Production | Schd 40, ASTM A36 |
REV1: Approved |
|||
2.2 | 1 | Pole long horzt | Production | Schd 40, ASTM A36 |
REV1: Approved |
|||
2.3 | 1 | Pole short horzt | Production | Schd 40, ASTM A36 |
REV1: Approved |
|||
2.4 | 2 | Pipe a 45� | Production | Schd 40, ASTM A36 |
REV1: Approved |
|||
2.5 | 1 | Support generator | Production | Sheet metal t:3mm, ASTM A36 |
REV1: Approved |
|||
2.6 | 2 | Base bearing | Production | ASTM A36 |
REV1: Approved |
|||
2.7 | 2 | Flange Bearing | Standard | Flange Bearing, square flange UCF206D1 |
REV1: Approved |
|||
2.8 | 2 | Flange axial Bearin | Standard | Flange axial bearing, UCF207D1 |
REV1: Approved |
|||
2.9 | 12 | Bolt for bearing | Standard | Bolt for bearing, Hex M10 DIN-934 |
REV1: Approved |
|||
3.0 | 1 | Transmission |
REV1: Approved |
|||||
3.1 | 1 | Working Shaft | Production | Schd 40, ASTM A36 |
REV1: Approved |
|||
3.2 | 1 | Shaft support | Production | Steel C45 |
REV1: Approved |
|||
3.3 | 1 | Shaft lower | Production | Steel C45 |
REV1: Approved |
|||
3.4 | 1 | Base motor | Steel C45 |
REV1: Approved |
||||
3.5 | 1 | Fly wheel small | Standard | Fly wheel small, D: 75.0 x 1 |
REV1: Approved |
|||
3.6 | 1 | Fly wheel medium | Standard | Fly wheel medium, D:150 x1 |
REV1: Approved |
|||
3.7 | 1 | Belt trans | Standard | Belt trans, type V |
REV1: Approved |
|||
3.8 | 1 | Generator | Standard | Generator |
REV1: Approved |
|||
3.9 | 4 | Bolt 1 | Standard | Bolt 1, Hex M10 x 50 DIN 934 |
REV1: Approved |
|||
3.10 | 3 | Bolt 2 | Standard | Bolt 2, Hex M10 x 70 DIN 934 |
REV1: Approved |
|||
3.11 | 7 | Nut | Standard | Nut, Hex M10 DIN 934 |
REV1: Approved |
|||
4.0 | 4 | Tensioner | Production |
REV1: Approved |
||||
4.1 | 4 | . Angle25 | Production | ASTM A36 |
REV1: Approved |
|||
4.2 | 4 | Turnbuckles | Standard | Turnbuckles, tensioner for guy of 6 mm |
REV1: Approved |
|||
4.3 | 8 | Rulldog grips | Standard | Rulldog grips, Grip 4 mm to 12mm cap. include nut and washer |
REV1: Approved |
|||
4.4 | 4 | guy wire | Production | wire of D: 6mm - total:4,60 m, Galvanized steel |
REV1: Approved |
|||
5.0 | 1 | Parking brake |
REV1: Approved |
|||||
5.1 | 1 | Break arm | Production | Steel C45 |
REV1: Approved |
|||
5.2 | 2 | Arm pivote | Standard | Steel C45 |
REV1: Approved |
|||
5.3 | 1 | Arm pivote2 | Production | Steel C45 |
REV1: Approved |
|||
5.4 | 1 | Grader plate | Production | Production Steel C45 |
REV1: Approved |
|||
5.5 | 1 | Brake cable | Production | Production guy L:2,20 m, Galvanized steel |
REV1: Approved |
|||
5.6 | 2 | Rulldog grips | Standard | Standard Rulldog grips, for guy D:6.0mm |
REV1: Approved |
|||
5.7 | 1 | Spring | Standard | Standard Spring, 20x90x4 |
REV1: Approved |
|||
5.8 | 1 | Bolt pin | Standard | Standard Bolt pin |
REV1: Approved |
|||